Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1990046members
1346958discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

FTD Migraton Uisng FMC

HiI dont have access to a  lab so am asking a couple of questions'I want to migrate from one FTD to an HA pair, On the FMC thats is currently managing the single FTD there is a sub doamin for the FTD but on the new FMC where I want to migrate the FTD...

BE7K Built in LAN1 and LAN2 Ports

We are trying to setup some redundancy for our BE7K's (BE7H-M5-K9) links by using a mix of ports on the motherboard and PCI cards as recommended in the Install Guide.The install guide lists the three ports on the motherboard as "Dual 1-Gb/10-Gb Ether...

bacase by • Level 1
  • 5 Views
  • 0 replies
  • 0 Helpful votes

Copy text/phone number from Voicemail Page

Is there a way to copy the text of the phone number of a voicemail that has been forwarded so that it may be pasted in the Calling Dial pad to call the person that left the voicemail back, instead of using the green Audio button that calls back the p...

LuSt by • Community Member
  • 8 Views
  • 0 replies
  • 0 Helpful votes

Resolved! PDMT cannot migrate WLC

Hi, Wondering if anyone has run into the following issue. Trying to migrate Prime to DNA center using the inbuilt PDMT but everything works except the WLCs will not migrate to DNAC. I've turned off SNMP v1 and v3 on the WLCs to no avail. One thing to...

elemzy01 by • Level 1
  • 581 Views
  • 3 replies
  • 0 Helpful votes

Firepower 7.42 issue interface Management0 has no link

I'm in the process of upgrading all of my firepower devices from 7.2.8 to 7.4.2 as it is the suggested release. we use the data interfaces as the management interface for most remote devices. As I upgrade each one, I'm now presented with a critical w...

Lee Dress by • Level 1
  • 107 Views
  • 4 replies
  • 0 Helpful votes

Firepower 1010 readiness check stuck at "Please Wait"

I have a Firepower 1010, on 7.0.0-94 that I'm trying to upgrade to 7.4.2-172. I ran the readiness check last night at 8pm.   12 hours later, at 8 am, it still says "Please wait" on the readiness check, and won't let me hit the upgrade button. Followi...

TCP optimization

Hello experts, We have a user with some performance issues, and he believes there is something related with TCP optimization enabled on Nexus switch that is degrading the performance due to some previous experience. Just want to confirm if Nexus has ...

noc tesys by • Level 1
  • 164 Views
  • 3 replies
  • 1 Helpful votes

Flex Config help

While trying to insert WCCP into the FTD, the configuration was wrong, TAC gave me the wrong type of ACL which broke the configuration of our running FTD. I have very limited knowledge of what or how flex config is. I need to remove the wccp part of ...

Resolved! Dialer Interface Question

HiHow do I check that all is ok with a Dialer Interface which is using Chap for authentication, is there any basic commands I can run to check all is ok, also I notice that the Dialer Interface dosent get an IP Address and never has but it does get a...

Load more