Is there an image where I can run EVPN-VXLAN on CML? I have tried the CSR8000v and the other IOS images but they do not have all the commands for EVPN. They have the BGP commands but not the tenant-side configs for the VRF/VNI mappings like here: htt...
Forum Posts
Hello Community would really like your help.Just purchased and installed CML, I only have the unamannaged switch and the external connector. I found similar folks with the same issue and they just had to load the ISO to the drive, which I have done a...
Hi, I have an Issue activating CML, the installation went smooth, I can now log in into CML software on my browser.The issue at first was that my VM couldn't access internet, Now I fixed it.When I enter my software license, i just wait for a good 2 m...
Hi support,how do I configure a CML server to be a HTTP or an HTTPS server? Can CML servers be configuresd to serve as EMAIL, DHPC , HTTP servers? How do I configure the CML servers? Thanks,Anthony
Hello,It's been at least two months I have been unable to do a lab on any of the CML sandboxes. I keep getting the error "Cannot create sandbox due to the following conflicts. One or more of the resources are already reserved"Then, it suggests anothe...
How to setup a small network using two cisco switches and two cisco routers to facilitate at least 4 people to do the configurations simultaneously?
I recently upgraded from CML 2.5.X (didn't check before I did the upgrade) to version 2.6.1. I am using VMware® Workstation 17 Player version 17.0.2 build-21581411.The upgrade did not throw any errors but when I go to use the GUI it show System Healt...
Hello After CML upgrade from 2.5.0 to 2.5.1 I cannot start nodes. I see "Failed to validate and define (Disk clone failed. Source image may be invalid or missing.)" I have all image definitions copied from refplat iso to disk. This was not toche...
Hi,Last week, I was able to reserve a CML lab as usual, but in the last few days, the reservation procedures took too long. Then, a window will pop up and say, Resolve conflict, and show only one faraway time slot (as shown in the image that I have ...
I have CML2 running on a VM in VMWare Fusion. I was able to login into the web ui after initially setting up the account, but now I can't authenticate the account in the web ui. I can authenticate in the CLI of the VM, but not in the web ui for some ...
Resolved! CML - License Personal - New VM
So I'm running a VM in a low end platform, I will purchase a dedicated machine to run CML as smooth as possible . I already registered the license that comes with personal in my account. Will i have problems activate the same license in my new deploy...
Hi all, managed to sort another issue thanks to this sub so thought I’d ask another question about an issue with a VLAN. Lab setup with an ASA 5510 and SG200-50P (I know no CLI but it was all I could get my hands on). Anyway I have set up 2 VLANs on ...
Hello,I've a problem with custom image IOS XRv 6.6.3 in CML. I've loaded it (qcow image) and attached as second under current node definition IOS XRv. In resule when I'm adding a new node IOS XRv, I can choose current IOS version (6.3.1) and new (6.6...
I am unable to get the Bridge external connector to work in CML 2.5.1. This was working on CML 2.1. When setting interface to dhcp, it won't pull an ip address. Setting a static can't ping anything. If I try running as NAT it works. Running on V...
This is driving me crazy. I have set up the CAT9800 WLC with no problem. I know how to access that device and what to do there....it's the "vWLC" that I'm struggling with....I've read several posts that state it can't be done..the "vWLC" cannot be se...
