in my scenario, I have two leaf switches in one fabric that i defined a VLAN-id ( 100 ) on them, lets's say VLAN 100 (vn-segment-id 4000) on leaf_1 is belonging to Costumer_A and vlan 100 ( vn-segment-id 5000 ) on Leaf_2 is belonging to Costumer_B , ...
Forum Posts
Hello All, I am seeing several Nexus 5672UP send the incorrect input and output interface identity. I am using SolarWinds as a SNMP and Netflow collector. I am seeing from and SNMP walk and show command that the correct SNMP identifier match in t...
Hi,Is it possible to connect asa firewall or any other firewall using evpn multihoming Thanks
Anyone have experience with a Nexus 9000 running in an endless reboot?I rebooted an N9K-C93180YC-FX24 running 9.3(10). I had intended to replace startup-config with a modified version to try out a new configuration ... but mistakenly skipped the 'cp ...
When connecting between Switch1 and Switch2 of Nexus9000 with different VLANs assigned to each other,I assumed that the Native VLAN mismatch log (see below) would be output like the Catalyst switch,However, nothing was output.Is it correct to assume ...
Hello,the scalability guide of ACI 6.0 says 500EPGs per tenant in a multitenant environment.we have here a fabric with 1500 EPGs in on tenant (whereby we just have 2 tenants and the second one is quite empty). moreover it is only a layer-2 fabric (no...
Hi Friends !I'm Going to configure VXLAN in my fabric and i have a very important question about external connections.Can we Directly connect our Border Spine/Leaf to the Service Provider and put the service provider physical port into a VRF called f...
post removed
Resolved! N3K-C3548P-10GX keep rebooted
Hi, My customer N3K-C3548P-10GX keep rebooted and caused a service disruption about 20 minutes. We removed this 3548 from the production network. When we did some investigation, we found a successive restart with death reason. May I know if this is a...
Resolved! A Question about N9K-C92348GCX
Hi friends,I have a stupid question about N9K-C92348GC-X. As I know, this switch has 48x1GE + 4x10/25G SFP+ and 2x40/100GE QSFP28 ports. The question here is can I use all the ports without any limitations? Will be any decrement in the capacity of t...
Resolved! Licensing on N9K-C93180YC-EX
HiAccording to the provided datasheet for Nexus 93180YC-EX, IF we want to use all 48 ports on the switch we have to have a license. Is this really necessary? or It is related to another product?Thank youPeyman
Resolved! Nexus 9000v Boot
Team,I am having a heck of a time trying to load and run the NX-OS 9000v. I know about the serial configuration. I'm trying to eventually get to the "leaving grub land" but I never get anywhere near it. And yes I know about the loader > and can run a...
Hello Everyone! Books?Trainings?Tips?I have 350-601 DCCOR guide but I would like buy 300-615 DCIT and 300-610 DCID in ciscopress.com, They do not have it available.
I am looking for confirmation and/or updated graph/document showing which ASCI the listed switch model below utilizes. The outdated graph is attached for reference. Nexus 93180YC-FX3: LS1800FX3Nexus 93108TC-FX3P: LS1800FX3Nexus 9336C-FX2: LS3600FX2Ne...
Hi all, I have a Cisco nexus N9K-C9372TX stuck in the loader prompt. I have the nxos copied in the bootflash. I have tried 2 options. First option - I tried to boot directly from tftp and received the following error: ################################...
