I have a situation where a customer has a large number of ATA191s in their environment. They are all in voice subnets where the desk phones on those subnets are being tracked correctly by CER but none of the ATAs show up in the subnet. I thought th...
Forum Posts
Can I use Cisco Jabber and have it so they can log in and out of a Hunt Group.I need a way for users to log in and out (Hunt Group?) to assist take calls to an extension.I don't think I have the option to use WebEx.I think a physical phone or Jabber ...
We have an ISR 4411 gateway connected to the PRI.Because SIPREC requires SIP-to-SIP, we introduced a C8000V CUBE in front of the ISR,The ISR still handles the PRI, but all SIP calls now flow through the C8000V.What we didConfigured the C8000V so that...
Resolved! IP DECT 6800 - IP DECT 210 in CUCM
Hello all, We are looking at options of cordless phones. We are aware of the 8821 and would rather not have a 802.11 wireless phone. Has anyone used the IP DECT 210/6825 in their CUCM environment?The other option we have is using an ATA191 and an an...
I am stumped! and Frustrated. Full stop. This is 2020 and I am still experiencing this issue for an upgrade in my LAB. I am trying to upgrade from CUCM 11.0.1SU2 to CUCM 12.5 SU2 and no matter what I do, I keep getting not enough space. Here is what ...
I have Avaya 1140e phones with my Cisco 9k series switch, configured with voice and data vlan. NO ISSUESswitchport access vlan Xswitchport mode accessswitchport nonegotiateswitchport voice vlan XXdevice-tracking attach-policy IPDT_POLICYaccess-sessio...
We're in the process of upgrading our old 7900 phones to 9800s, and I've noticed that the MCID button is not available on the 9800s after upgrading a few of them. I'm using the same softkey template as before, so I know it's not missing from that. I'...
Has anyone else had this problem. I recently put in an ATA, running 11-2-3MPP0001-028 Oct 24 2022 (So its the approved Zoom Firmware version). It was entered as a bug in May 2021, but seems to still be alive in kicking. Anyone else found away arou...
I have a number that's receiving calls forwarded to it that it should not receive. Is there any way to see what number is forwarding calls to another number? To be clear, I don't have the number that is forwarding the calls, just the receiving number...
hello Cisco Unified Communications Self Care Portali can't access this portal i get an error where does it come from thanks You do not have the required privileges to access this system. Contact your system administrator.
Hello - our company is moving our Security Operations Center from Teams to WebEx Calling. The remainder of the company will remain on Teams but it is important to preserve internal Caller ID so that when our SOC receives calls, they know who they are...
I have Dial Peers connected and inbound calls from teams are building a connection, but the connection is not appearing in Teams Admin: I cannot figure this out. All TLS is correct, certs are correct, dial-peers are correct, tenants are correct. I ...
I have set up multi-tenant in my Cisco CUBE. I needed to direct sip sessions on different interfaces. My question is, can I establish an ip address trusted list for each tenant or does it always reference the global voice service voip configuration? ...
Hi Team,Needing support. Need to replace voice gateway Cisco CISCO3925. Have two new router C8300-1N1S-6T.Is this a license issue? noted that that is different from cisco 3925.Bellow a sh license usage from C8300:sh license usageLicense Authorization...
Installing RTMT 12-14 Versions on Windows 11 requires Java releasesjdk 1.8_0 101, jdk 1.8_0 102; I installed 4 total versions including jdk 11.0.15.1 and jre 1.8.0_341.You must however follow these steps first in order for the install to work otherw...
