Hey all, I'm very new to networking, I've spent a long time trying to figure out why it displays this message "%DHCPD-4-PING_CONFLICT: DHCP address conflict" on a routerAny help would really be appreciated, thanks in advance!!
Forum Posts
Resolved! Interface Status
Hi, quick nooby questionDoes an interface goes down if the other end of the link is down ? in gns3 it doesnt happen, does anyone knows how it works in real gear.
Hello all, I like to see who or what is using most of the bandwidth (top consumers). My setup is like below. Cisco C3750 switch is connected to juniper srx cluster. Every connection is shared by firewalls via cisco switch. I like to monitor the bandw...
Resolved! SNMP Version 3 user password recovery
Hi all!!Hope you're doing great,I've been studying SNMP and I got this question asked:23) What happens if a customer does not remember the passwords for his SNMP v3 user?After doing some research I found this "Nodes table of database would have this ...
Hi Guys, new member here. Studying for my CCNA and currently trying to get a Cisco 897 VAG-LTE working over my NBN connection. I can get a connection to the ISP and my test laptop can obtain and ping the default router but I can't get internet access...
Hi, I am configuring a DHCP pool on a Cisco ASA5505 to provide the internal network (VLAN 1) with IP addresses ranging from 192.168.1.50 to 192.168.1.200 on a subnet of 192.168.1.0/24. However, I am getting an error that I cannot get a range of more ...
HeyI have a router a switch and a pc. My router can ping out to the internet and ping my pc, but my pc cant ping out to the internet.what to do?
Hello. We have 2 Layer 3 switches and multiple Layer 2 switches we want our layer 2 switches to connect to both for redundacny but only choose the primary route unless it goes down in which case it will take the secondary route. i have tried with spa...
Resolved! Rv340 internet speed issue
Recent I changed my home wifi router with Rv340when I checked my internet speed, the speed is reducedDoes this happen due to any router settingsIsp directly connected to router wan3 vlan configured
How do I configure a Nexus switch so that I can monitor / manage it with Cisco Network Assistant? I have snmp-server users defined, and a community, I have the http-server feature declared, but I'm not able to do more that see it as a neighbor in t...
Is there a way for the router itself to act as a SCP/SFTP server so a SCP/SFTP client can connect to the router and transfer files?
Greetings, I have some Wireless AP's that are AUTO training up in 802.3af power mode to our SG220-26P. I need these AP's to automatically train up at 802.3at mode. I can cli to the AP's and configure them at 802.3at power mode. That only works unt...
Hi all Is it possible to check if a switch/router is properly synced to an NTP server using SNMP ?via CLI it's easy by issuing the 'show ntp status' or 'show ntp associations', but can i somehow check this via SNMP ? thanks ! grtzthijs
Resolved! HSRP DMVPN
Hi team, I have two C1100-4p DMVPN Spoke routers and I want to combine them in HSRP, but the problem is that when I try to raise DMVPN in HSRP, it does not rise, and if I turn off one of the routers, then the DMVPN tunnel works fine. I do not underst...
Hello :) I have a RV260 router configured with OpenVPN server.I have 3 VLANS configured with acces rules.VLAN 1 (default) : 192.168.10.0VLAN 2 : 192.168.20.0VLAN 3 : 192.168.30.0VLAN 1 can acces VLAN 2 and VLAN 3 but VLAN 3 and VLAN 2 cannot acces VL...
