Hello, everyone ! I'm having problems with a SIP incoming calls. The infrastructure in place has the outgoing call-leg a controller E1 running ISDN protocol as below: PABX ----(isdn)----- CISCO 2911----(sip)----- SIP Server Cisco 2911 IP...
Forum Posts
router#sh run | sec event event manager session cli username "user" privilege 15 event manager applet syslog_redirect event timer watchdog time 3600 action 1.0 cli command "term len 0" action 2.0 cli command "show log | redirect ftp://10.10.10.10/log...
I try to configure the Embedded Event Manager (EEM) in my ASA5508 to perform an automatic task for me. The task is to automatically output the "show running-config" into a new file. I want to use this as auto config backup for my device. The problem ...
I'm trying to change the configuration on an NCS 5500 via SNMP. Most of the documentation online uses snmpset, so I've got that installed on a linux host. To me, it doesn't matter whether it's providing CLI commands or copying a new config from an FT...
Hello all, I hope this is the right community to place this. I am working on building a new server for use as our corporate syslog / ftp server as the exiting one is about to die. The old server is a red hat 5 where the new server is red hat 7. Old...
Hello, How can you make prime-infra ssh speaking with NX5K switches using cbr in place of cbc mode in their ciphers? Cisco Nexus 5672UP Switch, NXOS7.1, SSH v2 enabled No matching ciphers found: Client (x.y.z.a)supported ciphers: 3des-cbc,aes128-cb...
Resolved! 4331 upgrade issue.
Hi to all, I've tried to upgrade my 4331 router and in process deleted old image. Now it doesn't boot up and always goes to 'rommon' mode. Can anybody help me with this case?
I have a 2 Cisco Switches. The one switch connected directly to my router allows me to connect all my devices at 1000GB. All the ports are set to auto/auto. However, when I connect the two switches together and connect a device to the second switc...
Hi Wireless Community. does anyone know this problem? The client count for a wlc in Prime Infrastructure (Version 3.3.0) differs from the real client count on the wlc. It seems only newly connected clients are added to the counter in Prime, but disas...
Hi all, Recently, I started some writing in python that I thought might be useful to some. These are still work in progress, but nevertheless. i was developing on Solaris 8 and Python 2.6.2. CiscoSwitch.py is a class which uses rshell to check thing...
This is self response. I have found the following bug-id but this is about Catalyst 4000 series but it does not include Cat3650. CSCud34951 - percent Failed to read thread information, returned 2010 on and39;show tech-supporthttps://bst.cloudapps.cis...
Resolved! DHCP lease time change
Hello guys, I change the lease time on DHCP server on Cisco core switch but its still showing the old lease expiry. I want to renew all the bindings without disturbing the end user devices ? I want to accomplish this through dhcp server ? Th...
Hi I would like to do schedule a job to backup WLC config in Prime 3.4. I went to "Administration / Servers / TFTP/FTP/SFTP Servers", dont see a field to enter user credential for FTP/TFTP server.
When switch boots up what switch does the first thing? Please help me to understand this.
Dears, I have Cisco Prime 3.2.0.0.258 installed as virtual machine standard edition, used to manage 2 x vss catalyst 6807 with firmware s2t54-ipbasek9-mz.SPA.152-1.SY1a.bin , along with about 30 Catalyst 2960X All these devices are discovere...
