Is it possible to change the default port that the APIC-EM uses to connect to devices via SSH? I have a customer that doesn't use the default port of 22 and they would like to change this to their unique port.
Is it possible to change the default port that the APIC-EM uses to connect to devices via SSH? I have a customer that doesn't use the default port of 22 and they would like to change this to their unique port.
I upgraded our PI 3.1 UCS appliance to 3.2 yesterday from 3.1.6. This morning, it told me I had exceeded my license count. As I started investigating, I noticed it added most, if not all, of my 3850 switches as wireless controllers. Can anyone tel...
Ok this may be a blast from the past, but I returned from a week off to find that I could not log onto LMS 4.2 on W2K8 R2. In fact, I cannot start LMS at all. E:\>sc start crmdmgtd[SC] StartService FAILED 1053:The service did not respond to the st...
Hi, I am having issue with Cisco LMS. I am getting the following error: CONTEXT POOL FULL ERROR Please suggest any possible solution to cover this issue. Regards, NA
When I have a stack of 2960X's, lets say 4 in a stack, there are 4 flex stack modules total in that stack. If I am covering the 2960X chassis on smartnet, wouldnt the flex stack module be covered as well since its in the Chassis?
Hi all, We are currently centrally managing/configuring our Cisco 5508 Wireless LAN Controllers with a Prime Infrastructure Hardware Appliance (Version 3.0.0). We use MAC Filtering on some of our SSIDs and I have found that I cannot add an entry to t...
Good day How can i wipe password of a switch or bypass it without losing any configurations on it. Regards CHUMA MABINDLA
Hi. Regarding to the "ncs run test iops" in PI 3.x from CLI. How does the IOPS test works? Is the PI instanse creating a 8.6GB file and check how long it takes? Anyone have som information around this?
I am new to TCL scripting and am in need of some guidance. I have a script that should power cycle some voice ports when a user dials a set number. I am running into an issue with the application running the script. I have added the information in...
I am thinking of upgrading my router and switches with the following IOS version and will like to know if they are interoperable with ISE because ISE is currently implemented in my networks. IOS versions: 7.0(3)|4(7) 15.2.6E 3.6.7E 15.2.6E 03.16.6S...
We have 2 5508 wlc in our campus each have 175 ap license.We planned to updated our controller to 5520,is that possible to transfer the license from 5508 to 5520? thanks abiy,
I know my config is messy, I have tried everything I can think of to get this to work. Could someone tell me why my vlans will not route to the internet? (Also if you see anything that needs to be removed I would welcome that too) 870 Router Curre...
I am looking for a way to write a standby config script that has a lot of commands, but the line following the ios_config has a lot of commands that need to be set. Is there a way to chop it up so one line isn't that long? I tried many ios_config lin...
Hello, How can I clean this log from the switch? DHCPD-4-HA_CONFIG_MISMATCH: DHCP pool VLAN48_USUARIOS configuration on Active is not matched on the Standby Best regards
Hi All, Recently we have a POC for PI 3.1 to manage some switches and APs, everything goes well except for the mail notification. After entering SMTP server IP and sender setting in GUI, then we saved and test, however we couldn't receive any ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-11-2024 02:55 PM | ||
07-10-2024 01:26 AM | ||
06-25-2024 09:33 AM | ||
06-21-2024 11:13 AM | ||
06-09-2024 01:27 PM |
User | Count |
---|---|
3 | |
2 | |
2 | |
2 | |
2 |