Hello, We plan to export Netflow from C8200 to five destinations and want to know what is the max. number of flow exporter destination on Cisco Catalyst 8200 router.
Forum Posts
I installed a module in a 4451 Router. I can see the new subslot as shown below. I have activated it as shown by the last command. The issue is if I do a show interface... command I can't see it there, can't see it with a show run and can't get to...
For an IDS Design we would like to configure multiple RSPAN session which is working fine for some other Cisco Products like IE-4010-4S24P, WS-C3750-48TS, IE-3000-8TC…unfortunately we struggling to enable this on our IE-3300-8P2S devices using ie3x00...
Hey!I'm trying to filter all the traffic for a subnet that I announce via BGP session.Configuration:- a switch L2+L3- a server connected to the switch through two different ports- three vlans: ISP1, ISP2 and serversIdeally, traffic coming from ISP1 a...
Dears, I am trying to boot image file from rommon-2 mode in IR829 router, But there is an error rommon-2> dirflash:ir800-hv.srp.SPA.2.6.31ir800-ref-gos.img.1.3.4.1.gzir800-universalk9-mz.SPA.156-3.M8manifestfs_recoveredrommon-2> boot flash:ir800-univ...
Hello, I have a Cisco 9600 device in the network with aaa configure as below. Right now all access to the device require aaa authentication. I am going for a migration where I will have to change the management interface from current vlan 995 to loop...
Can I set up syslog on cisco acs for windows? If you have, please let me know the relevant documents or methods.
Hi I am trying to find out a command to know what version(s) of TLS are running on my IOS-XR and NX-OS devices. In IOS there is this command "sh ip http server all" to get that info. Is there a similar command in IOS-XR and NX-OS to get that informat...
Hello!i have prime inf 3.4i'm trying to make Templates that clear all interface counters and deploy to my switch.but when i deploy - Prime make error for timeout.On log i see that he waiting to conferm my command"Clear "show interface" counters on al...
The following description is about my problem I met. I used oneCisco Nexus SmartNIC K35-S(formerly X10) in a server to mirror TCP packets.I want to parse X10 frame data and extract the TCP packets and data. I called exanic_receive_frame function to r...
I'm stuck at an exercise of packet tracerCould someone help me with the requested configurations. All info can be found in my zip file along with the packet tracer. It would be super helpful to have the configurations that were made that are attached...
Resolved! Guidance required.
I have planned to do CCNA course at Cisco Lab. Whether the company provides such an option? If so, may I have the list of cities and addresses at which such training centres are located.
Hello! So. I created a test privilege level and then tried deleting it, but something went wrong ...switch1(config)#do sh run | i privilege username admin privilege 15 secret 5 $1$fTue$G09kULQtxRfTCyhPHLyzm1 username test privilege 5 secret 5 $1$9oF...
I've been contemplating my career path as a network engineer, and I wanted to get your thoughts on the relevance of Cisco certifications in today's dynamic tech landscape. I know Cisco has been a MyGreatLakes longstanding leader in networking, but wi...
I use a Cisco C4506 E with the vss method and use a wlc 5508 with SSO redundancy, here is the topology. I have a problem where the Access Point connected to the distributor switch connected to Chassis 2 cannot be pinged and there are some that cann...
