Anyone able to help configure AA on the ITS 2.1?? The config notes are a little "thin" on this issue. Thanks,Phil
Anyone able to help configure AA on the ITS 2.1?? The config notes are a little "thin" on this issue. Thanks,Phil
Here's the skinny...ADS, Off the Box Exchange, Unity.I am able to search existing users and begin to create new ones; however, when I try to change a user, it seems to allow this but the changes do not stick. When I go to add a newly imported user, ...
HelpWhen starting Unity Diagnostics I get Run-time error 8007045a, Automation error, A DLL initialisation routine failed. Do I have to re-register or re-load a dll?thsnks
What configuration change should be done in AS5400 to issue a second dial-tone to the caller ?Kiran
Hii have this error message but couldnt find any relevant informationcould anybody help pleasethe error is:%NP-3-NAKRSP: NAK Response Received - command 0x1501, result code 0x8005, msg id 0x15FF, session id 0x76, msg tag 0x0tks
Dear All,I have a scenario where i am using 2 routers each having 2 port FXS card. I am connecting both the routers back to back over ethernet port.I want to connect FXS card on either end to PBX and place a voice call through PBX (I am not having E&...
HiI've been searching for "descriptions" for the Device Logs on the Cisco IP-Phones, but haven't been able to find anything at all......Does anyone kow wthat the cryptographic messages meens?(found under the Device Logs' Debug Display on the 7940 pho...
Paul Cameron can you give me the answer here ?Why do inbound calls, when number unknown or private match dial-peer 991 or 992 inbound as apposed to dial-peer 1000 or 3000.debug Isdn q931 and voip ccapi inout attatched at bottom of dial-peers The sh v...
CM 3.2 2c, SP E. We have 1000 phones and users. When we do a global directory search in call manager with no specifics items for the search, the results are limited to the first 500 entries (creation) even if 1000 users has been created. Is it norm...
Is there any good links for end user training on IP phones.
I have Cisco 2610 voice T1 circuit connect PSTN T1 circuit interface.the 2610XM controller t1 config... (IOS is 12.2(13)T IP Plus) framing sf linecode b8zs ds0-group 1 timeslots 1-24 type e&m-fgdwhen I use my phone to dial PSTN T1 circuit number to a...
Does anyone have any links/information that they can share with regards to IPSec site to site tunnels and prioritizing voice traffic? I remember coming across something similar a while back, but I can't find it! Also, does anyone have any practical e...
We have an issue with long voicemails being cut-off without a warning you have "x" seconds left to leave your message. The user leaving the message gets cutoff, and the recipient's greeting plays over again. Is this normal? In addition, one user c...
I'm replacing a legacy PBX with CallManager.The current setup allows managers DNs to ring on both managers and assistants phone. When 1 phone call comes in either the assistant or manager will pick up. If the manager picks up the first call and a sec...
I have a customer who has a Musak live feed service and is moving into a location where this will not be an option any longer. Does anyone know of any services focused on custom music on hold messages and has an Internet streaming delivery we can in...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-13-2024 01:33 PM | ||
05-10-2024 01:42 PM | ||
05-07-2024 03:03 AM | ||
04-22-2024 04:46 AM | ||
04-18-2024 07:46 AM |