Hi all,We are planning to deploy CUCM solution for our client. With CUCM 7.1 & MCS7825, we want to use ATA devices either ATA186 or SPA2102 for providing telephony service through Analog phones.Q1) Regarding licensing, do I have to buy User Licen...
Hi all,We are planning to deploy CUCM solution for our client. With CUCM 7.1 & MCS7825, we want to use ATA devices either ATA186 or SPA2102 for providing telephony service through Analog phones.Q1) Regarding licensing, do I have to buy User Licen...
Client has MeetingPlace installed and want to use Scheduling. They do not want to move to WebEx. They have MeetingPlace 8.0 installed and want to add scheduling. The question I have do I have to order Scheduling seperately and do I have to orde...
Is it possible to block international calls on WebEX?
I have not been able to find a report of what numbers that WebEX has dialed too. Is there such a report? It does not look like that WebEX reports to my ISI Call Accounting software....Thanks
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/serv_administration/guide/7xcucservag040.htmlis there a document as to what function these services perform ?
Hello everybody,I would like to configure the DCM9900 (v. 10.0.02) in order to arrange the position where every channel will be tuned in our STB customers. I've read the manual and it seems that VCT (or LCN in some networks / literature) is not compa...
We are using Cisco 2921s to implement a land mobile radio over IP solution as a TDM E1 (radio lmr side) to Multicast gateway (for consoles/dispatch connections). We have experienced issues with the voice ports going dormant after momentary interupti...
I have been asked if I can remove some of the prompts from WebEX. Basically I think the boss wants to have WebEX call him and he presses 1 and is in the meeting.Is this a per-meeting setting or is this a global setting?
I had a defective DMP so I am swapping it out with a new one. I swapped them out, deleted the old DMP from the DMM and tried adding the new one and it is giving me a Error 400? Any suggestions?C
Hello Everybody,I have a MCS-7835-H3 Server, running DMS 5.2.1. The Server has 4 hard disk, (300Gb every disk). I've noticed one hard disk is alarmed, the led is color amber.I was looking for some documentation about this but i can't find anything.I ...
Hi ALL,I am using Cisco 3945E, IOS 15.1(2)T1 with radius AAA and heaving troubles with voice translation profile and radius attr.Here is a part of my configuration - incoming dial-peer voip and voice translation profiledial-peer voice 8 voip corlist ...
In reading up on WebEx Connect's cabailbilty for integration with Unified CME v8.8 and later in the recent version 7.2 release here: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme_webex/configuration/guide/webexconnect_cme.html#wp1062351My quest...
We have several phones with NonDID number on them. Our route pattern is setup to use an external phone number mask of the sites main number (1112223333). However on two of the phones, we would like to have a different number displayed (1112224444)....
Looking for any and all instructions on being able to integrate are existing Polycom HDX 9000 Video Conferencing System with WebEx's Meeting Center product.thank you,David
We migrated from a Nortel PBX to Cisco CM with our Polycom analog phones connected to VG224s. However the codes we would use to transfer, conference, etc. no longer work. Assuming that our VG224 is configured correctly, is there a list of feature cod...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM | ||
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM |