Other Network Architecture Subjects

I am connecting up a 2950 to a 3550, which in turn connected up to a 6509. The 6509 is the VTP Server and all others are clients.When I connect up the 2950 to the 3550 as a chain and the vtp set to client, it always changes it to Transparent thereby ...

i have two cisco switches 4507 and 3750G-24 , i have to fiber link between them on the 4507 on port 3/2 and 3/3 , on 3750 on port 26 and 28 , i want to make merge between them to be as on port and make load balancing between the , please any can giv...

MST can achieve fast convergence on a port ,the protocol relies upon two new variables:edge port and link type.Link type is automatically derived from the duplex mode of a port.How about edge port ? Do I need manually config edge port with 'span port...

Hi;i have isdn 64 k line which i am trying to connect to inter net. but its not connecting ...i debug the q931 and found below massage:*Mar 2 01:47:06.385: ISDN Se3/0:15: RX <- INFORMATION pd = 8 callref = 0x001A *Mar 2 01:47:06.385: Calle...

i enable port-security in one port of my catalyst 2950, and add a mac addres for this port and if it wasnt the mac address the port will shutdown because the violation, but i did this in 4 ports, and only work in one because in the other ports even i...

I have two 6509s with Sup2/MSFC2s. I have HSRP configured between the two MSFCs. I periodically receive the message shown below. I have several Vlan interfaces, and it will occur on different Vlans. My HSRP address is .1, the two switches are .2 ...

Ok, we use 3662 at hq's to connect to 1760-v's and have t-1's to each location... have a store that everything works; data, voice out, but voice in does not...here is info from 1760:Store129#sh dial-peer voice sumdial-peer hunt 0AD PRE PASSTAG TYPE M...

I am running a c2600-i-mz.122-5a.bin on this router and it is doing NAT as follows for both source and destination.interface FastEthernet0/0 ip address 10.192.57.228 255.255.255.224 ip access-group 101 in ip nat inside speed auto full-duplex!interfac...

Can I connect a dial-in modem to a Catalyst 6509 with a sup720? There's no mode switch for con 0.Thanks!

Hi,I wish to know if the WS-X6516-GE-TX line card can support half duplex command. Aaron

Whenever one of my users start vmware on their workstationt that has port security configured, the port shutsdown. The configuration looks as followsset port security 3/2 enable age 0 maximum 5 shutdown 0 unicast-flood enable violation restrictI have...

Iv been searching trying to find a way to confine HSRP multicast traffic between the two HSRP group routers for all the VLAN's that have HSRP groups, but I have been unable to make it work. Iv setup ip multicast-routing and entered ip pim sparse-mod...

I have a 3750G-24TS that I need to attach a RJ-45 10/100 port firewall. The 3750 is on a campus site that is fiber attached only to the computer room. I need to place a firewall that has only RJ-45 10/100 ports to the 3750 fiber port. Is there a reco...

[ Cc: Enterprise Data Center Forum ]Hi all,this is related to discussion:http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=LAN%2C%20Switching%20and%20Routing&CommCmd=MB%3Fcmd%3Ddisplay_location%26locatio...