I need to know the memory DRAM of the Router 2611, when it boot, there is some information about of the Memory DRAM. I know that the Flash memory is 8MB, but I don´t know if the memory DRAM is 32MB,Thanks You, for all.
I need to know the memory DRAM of the Router 2611, when it boot, there is some information about of the Memory DRAM. I know that the Flash memory is 8MB, but I don´t know if the memory DRAM is 32MB,Thanks You, for all.
I am converting from a sup2 Native IOS to a sup720 IOS and I can't seem to get these command to work. I can an error mesage VLAN 1 TLB 1 VLAN 1002 has inconsistent TLB values (0 / 0). The command is for each of the vlans.Vlan 1 vlan 1002 tb...
I cannot see the memeory of VIP4-80, but the VIP is working normally:Router#show diag 0Slot 0:Physical slot 0, ~physical slot 0xF, logical slot 0, CBus 0Microcode Status 0x4Master Enable, LED, WCS LoadedBoard is analyzed Pending I/O Status: NoneEEPRO...
We have switched to Frame-Relay with WorldCom or what ever name they go by now. Traffic shaping was employed without request here by one of my colleagues with the help of first or second level Cisco support. I feel either this is not set right, or we...
Hi,I'm trying to set up the router to the Cisco manual and the book shows the commandsROUTER(CONFIG)# interface bri0ROUTER(CONFIG-IF)#However the router will not accept the 'bri0' part of the first instruction.Can anybody tell me what it should read ...
Hello,I have a CAT4006 with SUP 3 running IOS (not CatOS). I upgraded the IOS from cat4000-is-mz.121-19.EW.bin to cat4000-i9s-mz.122-20.EWA.bin After the upgrade the 4006 switch stopped issuing dhcp addresses. I recreated the IP dhcp pool without su...
Why i do not have "sh ip nbar version" command? I've tried on two routers with following IOS-esc3640-is-mz.123-6a.binc2600-is-mz.123-10.binand does exchange protocol resognition work with NBAR. I do not belive that NBAR recognies dynamic ports assign...
I'm having trouble installing the 5.0 IDU on my Ciscoworks LMS 2.2 system. This box has been running since the inception of LMS. Prior to upgrade I was running RME 3.4 with IDU 4.0 patched. After I upgraded to RME 3.5 I get a severe error message ...
Suppose isolated ports in a PVLAN (all in same subnet). Is it possible to provide layer-3 connectivity between those isolated ports? A whitpaper about PVLANs on CCO says that if a host goes to the def gw instead of directly going to the same subnet h...
Hello,I'm going to implement DHCP snooping in a C4006 in a production environment. Is it a disruptive configuration? What would happen with all the IP addresses that were assigned prior to the configuration of snooping?Any advise would be appreciated...
Is it possible to have the RME syslog analyzer listen on another port different from UDP 514 ?
how many simultanous monitor session (SPAN) can i configure in a cisco 2950G
hi all ,I am trying to log login access for Telnet to the netwrok devices ,below is the access-list that i used ,access-list 155 permit tcp 140.80.0.0 0.0.255.255 any logaccess-list 155 deny tcp any any range 0 65535 logaccess-list 155 deny udp ...
Hi,Can someone explain, for OSPF routing over NBMA it is necessary to provide neighbor commands to establish neighbor adjacencies.Why the same is not needed with eigrp? Let's hv the nbma cloud as the frame-relay for example.
I recently implemented a swicthed LAN network using 2 Cisco 3750s L3 switches & and a bunch of 2950s all trunked to the 3750s. The 2-3750s are connected via a stackwise cable. There are 4 VLANs (10.x.60.X, 10.x.61.x, 10.0.62.x & 10.0.63.x). Routing b...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |