Dear Members, I had one typical problem. We have IBM blade center HT chassis. Four blade servers are used form this chassis, connected to BNT switches and in turn BNT switches are connected to cisco 4948 switches. I am unable to ping default gate...
Forum Posts
Hi Team, If you are using nat for RDP how it will be safe in cisco devices ? Anyone whose know the ip can able to access the devices. Please anyone explain to me.
Are you able to assign the same VLAN number to a VNI as long as it is in a different VRF in regards to Spine Leaf VXLAN architecture? Is it best to keep all VLANS/VNIs in same VRF for simplicity?
I have a cisco ISR4431/K9 running isr4400-universalk9.03.13.02.S.154-3.S2-ext.SPA.bin. Trying to upgrade to isr4400-universalk9.03.16.05.S.155-3.S5-ext.SPA.bin. md5 checksum has been verified, config register is 0x2012 rommon version is 15.4(2r)S ...
The NAT configuration guide ( https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-16/nat-xe-16-book.pdf) mentions the following as one of the restrictions (on page 25) > NAT outside interface is not supported on a VRF. How...
Hi All, Basic architecture of the above network is: -Collapsed core/distro utilizing a stack of two 3650s -Edge/workgroup switches are other brands -Each workgroup switch represents a separate /27 ip subnet. -Each workgroup switch supports LACP and...
My Association is not coming UP with the following configurations - Please suggest crypto isakmp policy 2encr aes 256hash sha256authentication pre-sharegroup 14crypto isakmp key XXXXX address <IP Address> crypto ipsec transform-set aes256 esp-aes 2...
Hi friends I want to deply WAAS_Express in 2901 router. according to cisco documents 2901 support the waas experss but there no any licese for waas express. so I buy the WAAS_Express license for 2901 and try to install that in the router, but the res...
Hi All, Ive got the CICM Express running and I can see the router its connected to. I can open a session to the UCS-E but it appears theres a firmware issue, so i upgraded to 3.2.2 which it took OK but now I get these errors: recovery-shell...
So I have 1 ShoreTel phone that is causing me some difficulties.This configuration has not caused me any issues on multiple other ports/switches so far, but for some reason this particular phone will not register it's MAC once I enable port security....
Resolved! Ipv6 image for 2610
Hi all Can anyone recommend the correct image to download to enable IPv6 support on a 2610 router as shown below. Also a link to the image would be great. Thanks in advance for your help, greatly appreciated. regards Cisco Internetwork Operating ...
I have aaa setup to use radius on my switches. The radius server sends an AV-pair for priv-lvl=15. SSH works fine. HTTPS works fine (I have one SMB SG300 and the CLI is too painful to use.) When I console in, I can authenticate the user but, it defau...
Hello community, We are using APIC-EM, and today when we tried to add a new device we saw that it keeped as "unknown" state (see the attached image), we tried to delete and add the device again, also we tried reloading the device but that didn't ...
Good afternoon I'm running into a wall when trying to create a script that'll go through my terminal server (C2811) to configure a new (Catalyst) switch. I've tested this code on the C2811 and it works fine, but it seems like once its going throu...
Could anyone tell me how to get one of my interfaces back into it's etherchannel? This is the message I get regarding the interface. Port state = Down Not-in-BndlWhen I do a show ip int brief I get the "down - down"As you can see the ports are co...
