Dear Forum:I found some examples about PPP Callback with TACACS+ server.I ask if there is some solution or example with RADIUS server.I cannot found it.I´ll appreciate your help.Thank you.
Dear Forum:I found some examples about PPP Callback with TACACS+ server.I ask if there is some solution or example with RADIUS server.I cannot found it.I´ll appreciate your help.Thank you.
Is it possible to bond multiple RFC 1483 interfaces? I can't seem to find any documentation on it.
I have a question regarding modem responses on the AS5300. If a call is issued from one of the modems and it hits a number that is engaged it waits over 30 seconds and then comes back with, "NO CARRIER". Does the AS5300 not come back with BUSY or som...
Hi,After upgading RAM from 128 MB to 256 MB on 2621XM commands: 'sh ver' + 'sh mem stat' show only 128 MB. 'Sh c2600' shows 2x128MB.What's the problem and does the router use all the available memory. I enclose output from these commands.Thanks for ...
Hi,I am looking for a bit of clarification of my understanding of how cef load shares.I have a OSPF network with equal cost paths with CEF enabled, show ip route displays the equal cost paths as I expect.My understanding is that CEF will load share o...
helloI have internet from two backbone broadboand ISP,and I want to loadbalance both of them , (i.e. two inputs from both ISP and one output internet ), so if I can double my bandwidth and I have more redundancy how can I do that with 3550 swithch w...
Good day!Here's my question: I have one server with two NICs working in team mode.The NICs are connected to two different switches for redundancy.The switches are interconnected. Now, how do I manage load balancing for data going to the server?Thanks...
4507R with dual 4013+ running 12.2(18)EW with (2)4418-GB, (1)4148-FX-MT and (1)4148-RJ.Trunk config applies as expected to 4148FX ports:interface FastEthernet5/1 switchport trunk encapsulation dot1q switchport trunk native vlan 99 switchport mode tru...
What are, in a nutshell, the differences between the NM cards and the WIC cards?
Is it possible to be configured 10Mbps ethernet(AMD Presidio2,2611 IOS12.0(7)T) in full-duplex mode? Router accepts IOS statment (router(config-if)#full-duplex) but interface's neighbour negotiates in half-duplex mode.
If we have two IPs configurated in an interface (primary and secondary) since we prune to do in order that the hosts of both subnets cannot meet?Thank you
Hello,Does anyone have recommendations on how to build a cheap lab at home, and what / how to configure?I have the CCIE practical guide, but it's ... um... okay.... I guess...Any info would be great
Is it recommended to create a new VLAN within a switched environment, involving numerous switches with redundant links, during the normal working day. When the new VLAN is created am I correct in thinking that the trunk links will go through the list...
I have been trying to have a mutual redistribution from OSPF TO BGP(please see attachment). I have 1 remote site and 2 local sites. connection to the remote site are 2 internet DS-3 running BGP with ISP and I have VPN tunnels running ospf. I have 1 e...
Hi,I need to know the routing table size of the switch.Thank you in advance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |