Other Network Architecture Subjects

HiI have a 1721(with a wic-1am card) as my dial in access server. I can dial in successfully using Windows 2000 and ping the Ethernet interface IP of 1721.But I cannot ping the IP of another router A which connected to the access server 1721 through ...

I have a 3700 router. I simply want to redirect all incoming packets on port 1 (int fast 0/1: 192.168.1.6 255.255.255.0) and send them back out port 0 (int fast 0/0: 192.168.2.3 255.255.255.0).I have been using the steps in "policy routing" but no i...

Hello ,I have 3 2950 switches ,switch1,switch2,switch3.switch1 is connected to both switch 2 and 3.I have a websense server that is connected to port 17 on switch 1.This websense server has 2 nic cards.One to send the traffic out and the other to mon...

What is the ramification of removing the IP address from one of my switches?I have a switch that I don't want to do any out of band management with. All management will be with a console cable. I don't want it to have an IP address. Will this affect ...

HelloA customer is using a router to translate X.25 packets into TCP/IP packets. X.25 packets are generated from a PoS and are processed by a proprietary application waiting for a particular 158-bit packet at the beginning of the transaction. If the ...

Hi there,In every Cisco device in our network we have a flash-card. There we keep a backup of the IOS/CATOS and the configuration file.Is there a program out there which we can use to automatically backup the configuration file to the flash-card ever...

Does anybody know if you can use a BRI-4B-U as an ISDN switch. Similar to when you use a 2522 as a frame switch.

Seem to be unable to log messags from the 3600 (IOS 11.x) to Kiwi syslog.commands i have usedlogging trap warningsloging host ipkiwi syslog is listening for snmp traps via 162.there is no access-list on the router interface i'm trying to log events.a...

Two companies merged with the same address space, so we need to NAT the destination (servers) addresses. Workstations from router_1 originate traffic to servers on router_2 and the servers addresses need to be translated. For example, workstation 172...

My site is connected to the main site via ATM wan link. There is a PIX 525 behind the router at my site. All internet traffic flows through the main site and then to my site, i.e. I have no direct internet connection. I am using a private address ran...

Hello!I have a 1601 Router with an WIC-1B-S/T installed. The IOS version is 12.2(17d).The BRI is used to interface the router with the X.25 network (X.25 over ISDN D-Channel). A host connected to the router by ethernet shall be used to receive all th...

I just installed a new Cisco Catalyst 3750G-24TS-E switch into one of my server racks. I configured its IP address and all that fun stuff and then I then installed a GLC-SX-MM SFP module.At the other end is our 4506 Switch and it only has copper 1Gbp...

Can a Cisco 3725 router with 256MB of DRAM handle a full BGP feed? The router is handling about 4Mb of traffic as well. Does anyone have a similar setup that can share their experiences?Thanks.V/

I want to transport two Vlan originated from my 7206 on a single FE, through the 2950, up to the GE interface of my UBr.I configured my two routers with encaps dot1q, an vlan id 100 & 101.I created two trunk port on the 2950, allowing the transport o...

HiAnybody has experience to convert power redundancy mode to combined mode on 4510R? Will this need to reboot the switch to take effect? Any document indicates this? Thanks