I am going to buy a 4503 with Sup II- PLus and a 48 x 10/100/1000 card (WS-X4448-GB-RJ45). I need to know if I can configure jumbo frames by gigabit port with this hardware.I have not found any information related to this Ethernet card.
I am going to buy a 4503 with Sup II- PLus and a 48 x 10/100/1000 card (WS-X4448-GB-RJ45). I need to know if I can configure jumbo frames by gigabit port with this hardware.I have not found any information related to this Ethernet card.
Hi I inherited a 2900 XL switch, I tried to connect to it through console cable but unsuccessful ! When it boots up it works fine and goes through the right sequence ! I use the hyperterminal bits per seconds 9600 , data bits 8, parity NONE , Stop bi...
when ethernet interface with ip 10.0.1.0 is shutdown which update message will be seen in the router when u issue debug ip rip?A- subnet 10.0.1.0, metric 0b- subnet 10.0.1.0, metric 1c- subnet 10.0.1.0, metric 15d- subnet 10.0.1.0, metric 16
Dear All,May I know if there is any compatibility issue between GLC-SX-MM and WS-G5484 provided that I have the right patch cord. I want to make sure as I connect Cat3750 and Cat3550 using GE.ThanksRegards,Raymond
Dear all,I was trying to connect a Cat2950 to a Cat3750 via their gigaports. The 3750 was set with auto MDIX.I was using straight cat-6 cables. The connection is not up. Any idea?Thanks a lot.Peter
hey folksI am told to configure a network which consists of a 10 sites and a centre. Each site has 2 2955 switches connect to control center. The center has 2 4503 switches. There is no requirement for the network.Folks, What should I configure on th...
Hi I have a Cisco 7505 in which i got a VIP4-80 installed with a PA-MC-8TE1+ and a OC3 PA. The OC3 card is recognized but the PA-MC-8TE1+ card does not show onShow Controllers orShow versionAlthough it does show on the show diagcommandThe IOS version...
I have a customer with a NAM-1 which has recently been upgraded to the latest version of code. They are very pleased with the new functionality but there is one feature that would make their life better.What they would be looking for is to have seve...
What is the loop back address used for? A. Determines the port number B. Determines Value of IP address. C. Test to see if IP is configured and working properly. D. None of the choices
is the fatethernet offers a speed icrease one hundard times of the ethernet?
i have 2 2503 routers and a 1900 switch making up my home network they are configured with nat with nat outside gettting its ip via dhcp from the cable co. everything works great but the internet stops working after 1 hour, i can start it again by re...
Dear would anybody like to tell me that what is the benefit of making a router bridge.And how can we do this pls help with url etc.
Hello, We have a unique problem hope you can help. We have 2 offices each has a cable modem and cheap router. 15 pc's in each office. a printer and server in one office (all pc's) that both offices must access. the other has 3 pc's and the rest Mac's...
Hi, I am currently using SAA in our network to perform monitoring of certain ip addresses through icmp echos. From the router prompt I can get all the information I require about the status of these probes by using a "show rtr operational-state". I w...
Hi all,can anyone pls let me know why do i get this error,i used to get on joined bridge or left bridge notifications,But now i also get the below error, how do i stop it.Error Message %SNMP-5-LINKTRAP: Link Up Trap -- ifName=9/31Explanation ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |