Is there any Cisco works IP telephony monitor product that can be installed on solaris. I have ITEM2.0 but this is for Windows only.Thanks
Is there any Cisco works IP telephony monitor product that can be installed on solaris. I have ITEM2.0 but this is for Windows only.Thanks
Where can I find a C programm that send configuration file to Cisco router from linux workstation?
I need to have the possibility to create 60 Vpi's (from 10 to 70) with an Atm Ima card, as I have to connect my 2651xm router to a carrier Atm switch that supports values from 10 up to 255 I would use the AIM-ATM module with VWIC's, but I need confi...
I have been searching if vtp have a number port associate, but i didn´t find it. Does it has it?
I am trying to get the SDM of a 1721 router working, that has a WIC card installed. I have connected the light blue Console cable into the serial port of a laptop and the other end into the back of the router marked Console. However whenever I open I...
We currently have three 3750 switches all connected via 2Gb fibre links. The problem i'm having is configuring one of our 2Gb fibre links to be the preffered route. This was done initially using the port-priority command on both ends of the link that...
Dear All,I am sure you get this a lot but i am new to the world of Cisco and our company has just purchased 10 of these Routers for our remote sites / teleworkers. I started to configure them through SDM but released that there is no where to input ...
hi again...I want to import the inventory existing from a CW Server(W2K) to another CW (also W2k).Is this possible?
I have a 3 year old 2924xl switch that is dropping Telnet connections. In another message thread, it was suggested that I update the firmware. From the Show Ver I get: cisco WS-C2924-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K byte...
I would like to get via SNMP the broadcast counter that is shown with a sh interface VLAN X"Received 387377 broadcasts"In order to have a picture of how broadcast traffic is incrementing in each VLAN.I am doing this cause i consider our network is to...
Hello.Can anybody explain the following. IOS Feature navigator for c805-y6-mw.123-9.bin does not list CBWFQ and LLQ among available features. But the foolowing configuration works:class-map match-all voice match access-group 194class-map match-all si...
Hello!I have some problems with Cisco Works Monitoring Center for Performance for Windows. I can not include device for monitoring. I tried couple of times to include from RME or manually importing, but with no success. Did anybody have the same prob...
Hi,I am trying to establish OSPF 'FULL' Adjacencies between a Cisco 2621XM and a Nokia GSM Switch (MSC/HLR). I have tested several IOS:1)IOS Version 11.xIn that case, the two neighbors have 'FULL' Adjacencies, that's fine !2)IOS Version 12.xThe two n...
Having trouble setting up, probably the most basic setup ever. (Beginner)We have a lease line and two 2600 routers each fitted with a WIC-1T. Im trying to setup our routers for network traffic can go between each network, the setup is as belowNetwor...
I have a C-831 isolating the enterprise network from the consultants network. Now I need to have a second port off the C-831 connected to a VLAN to extend the consultant network. Do I need to use a cross-over ethernet cable when I have one of the 4 p...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |