Other Network Architecture Subjects

I'm having trouble understanding how rate-limit works. Let say I want 10Mbps and want to burst to 20Mbps how should I setup rate-limit? What I would do is the following:rate-limit input 10000000 20000000 20000000 conform-action transmit exceed-actio...

We have a pair of MGX 8830 with PXM-1E front and PXM-UI-S3/B back. We need to connect a dial-in modem to the console port of the PXM-UI-S3/B. Can this be done? I'm only aware that you can only connect the modem to the maintenance port which does not ...

Hi AllWhen I do a show interface s0/1 on my 2620 router, I get the following:Serial0/1 is down, line protocol is down Hardware is PowerQUICC Serial Internet address is MTU 1500 bytes, BW 192 Kbit, DLY 20000 usec, reliability 255/255, txload 2...

Hi all i m tried searching an IOS which can be used in my 1751V to support Dynamic IPsec vpn client connections.my 1751V have 32Mb DRAM and 16Mb Flash.I tried searching IOS which can suit all these conditions.if neone of u already running with the co...

Current network setup:(3640, serial) ------T1-----> (serial, 1721, FE) --> Branch LAN (hubs, switches from other vendors)All devices on a single bridged network (vlan80)New network requirment:Branch LAN vlan80 will be extended to another building usi...

I'm going to install 6513 switch and have a difficulty to connect Ground cable.I found a small hole in the chassis(below of slot 13 and above of power supply) and I have a ground package shipped with the switch which includes one grounding lug and tw...

We have a Cat-2980G-A connected to an RPS 300. Yesterday, the log on that switch started showing the following messages:Power supply 1 okayPower supply 1 failedPower supply 2 okayPower supply 2 failedInsufficient power supplies operating, this system...

Hi!I would be very grateful for explanation situation why in routing table i seeD* 0.0.0.0/0 [90/33280] via 10.15.0.2, 00:31:53, FastEthernet2/16 [90/33280] via 10.15.0.9, 00:31:53, FastEthernet2/14but in topology tableP 0.0.0.0/0, ...

I'm trying to configure my soho97 router with adsl, but it doesn't works. I'm in the UK with a fixed IP address and using pppoa, chap, vc-mux and pvc 0/38.from the internal lan I can ping int e0(10.10.10.1) and int d1(82.x.x.x) with no issues, but 1 ...

Hi,I have encountered a problem with FTP when going out through one router and coming back through another. Each router is running static NATs and has the same static NAT translations. However, if a connection goes out through one a router and back...

I'm building up a bunch of 2620's using WIC-1DSU-T1 modules. It looks like I have a bad module and was wondering if an older FT1 CSU/DSU would work in the new routers. The new modules have a hardware code of PQUICC and the older WIC has HD64570. T...

Hi all, I would like to know what Cisco says is the ideal way to set up redundant WAN links and do load balancing also.

I'm tryng to access CMS of a Cisco 3550 SMI IOS 12.1(11)EA1 with this aaa configuration: aaa new-model aaa authentication login login-pwd group tacacs+ enable aaa authentication enable default group tacacs+ enable aaa accounting exec accounting start...

I have a pretty easy problem but i just dont know how to solve it. There's a cisco 827 router here, when i telnet to it, and i wait for about a minute the connection to the host is lost.And another question, how can i change the duplex mode of an eth...