Hi,I would like to know If I can send the Cat 1900 syslog to the CWorks server and how I can do it, because the switch doesnt have the logging command.Thanks!
Hi,I would like to know If I can send the Cat 1900 syslog to the CWorks server and how I can do it, because the switch doesnt have the logging command.Thanks!
Does anyone know if there is any recommended guidelines for rebooting Cat 4000/6500 series switches periodically to clear buffers, etc (for maintenance? I appreciate any advice you can give. Thanks.
Hello,We have 2 IGX 8410 interconnected via an E1. It carries frame relay PVCs and interconnects 2 PBX for radio communication all within the same E1. Both are part of a national data/voice network of about 30 IGX.We've been working for about 2 years...
HiWe need to setup a 6509 switch to allow inter-vlan routing. The routing should handle ip and ipx. The 6509 is installed a msfc2 with supervisor engine 1A. My question is that, do I need to upgrade or buy anything to make ipx routing work between di...
My customer has a 6509 with a NAM card in slot 9.If you do a 'sh vlan' for vlan1, ports Gi 9/1 to 9/5 are in vlan1.From the switch console if you try to change to the port in conf t mode, you get'This mode not available for these ports'Is it possible...
I have a "production" lan and a "test" lan that is a perfect clone of the production in terms of hosts, applications and IP addresses.Of course the 2 lans are completely separated and only the 1st one has an external access.I would like to grant acce...
I have 2 sites linked by 2 2MB circuits each with its own router. I need to implement PBR to move some video conference traffic from the main circuit to the backup circuit.(ID by host ip addresses at each site.)The problem is I need to monitor the ou...
on pagehttp://www.cisco.com/en/US/tech/tk828/tk363/technologies_white_paper09186a00800d6b63.shtmlthis does not look correct. Please can someone at Cisco confirm this. (check the auto-rp announce/discovery loopbacks)On my config, i was going to use ...
I have an easy question for you guys.How do I save the running config on a Cat 5500??Thanks,Bob
Hi All,I have three Cisco 1751-V routers used for VoIP over wireless WAN connection.I would like to program one of the router to periodically send ping to the other routers and in the event of a time-out to send an e-mail to system administrator.I ha...
Have been unable to determine if CW is capable of monitoring other elements such as servers etc. Is there a special module that allows this - or is it capable of it out of the box and I haven't found the "how to" yet...thanks.
We are seeing an issues almost exactly as described in the Switch Release notes (excerpt attached), but have not been able to get a definitive answerfrom Cisco or Intel on when this has a a fix in either the Intel Pro/1000T, or in the Catalyst 3750. ...
Good Morning ALL,I am thinking to increase my level of redundancy in my networkk using all the available Ethernet/Fast ethernet interface in the router used as default gateway from the LAN in the remote site (in an Hub and spoke configuration).My pro...
Is user tracking able to discover hosts that are connected to a router interface or is there the need the have hosts connected to a switch port, so that a CAM table is available?We have a router's token ring interface connected to a token ring hub th...
Hi,wonder if someone could tell me what Managment program will give me utilisation stats on my 2 Cisco 1603 routers and 256K private circuit that connects them..I am having some delays on recieving and sending and want to know what bandwidth is used ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |