I've 3 router which fully meshed. (a to b, b to c and a to c)Do I need one or two as route reflector? How about the cluster id ? do I need to assign different cluster id in each router in order to avoid the loss of redundant?thanks for any help
Is it possible to configure a dial backup interface (ISDN) to inherit the IP Address of the WAN Interface (Frame Relay) which it backs up?The question stems from a situation wherein a network has existing IBM 2210 Routers connected via Frame Relay to...
Hello:I have to install a ISDN wic1bu to my existing 2610. I am currently using this router with a T1 CSU/DSU connected to a 384k serial dedicated line to my provider for internet access. I want to be able to have redundancy when my primary 384k line...
Hello: I have to install a ISDN wic1bu to my existing 2610. I am currently using this router with a T1 CSU/DSU connected to a 384k serial dedicated line to my provider for internet access. I want to be able to have redundancy when my primary 384k lin...
My network is 3640,7500 and four 6509 msfc interconnected with ethernet vlan 200,like this:6509 msfc(10.1.200.250)----vlan 200----3640(10.1.200.246)6509 msfc(10.1.200.251)----vlan 200----7500(10.1.200.248)6509 msfc(10.1.200.252)----vlan 2006509 msfc(...
Will someone please help me out on how I can discover the kind of Application protocol that ar bieng used by my clients, and the percentage of usage of these protocols in relation to the total bandwidth given to the client.
IOS 12.2 documentation states that Policy Based Routing (PBR) can now be fast-switched. However, it states the following fast-switched limitations:1) The set ip default command is not supported. 2) The set interface command is supported only over poi...
I have next situation:R1(s1/1-192.168.100.2) in City1(LAN - 10.10.0.xxx),R2(s0/0.2-192.168.100.1) in City2R1 connect to R2 by FrameRelay.================I run #sh ip mroute at R2------------R2#sh ip mrouteIP Multicast Routing TableFlags: D - Dense, S...
Hi All,My colleague asked me a question from ipexpert.net:Messages for ICMP traffic on R2 should be able to see Frame-Relay L2 circuit ids in its debug traces for granular verifications. R2 is connected to frame-relay interface.I had tried to search...
Hello, can someone explain to me how to configure a NAT scenario that will cause the router to switch to the second ISP interface for translation if the primary fails. There is no BGP failover involved, just floating static routes. I think I know ...
I am looking for the proper mib (and mib variables) to use in the calculation of utilization for an ADSL interface. Obviously I cannot use the standard ifSpeed mib variable since the speed is different in each direction. Any help? Does this even ...
Hello,I have to implement on two routers us as bridge a backup PRI.Here are the configurations of the two bridges.I cannot use dialer watch because we are in bridging environnement.Do you think it will work without problem?Or i search exemple configu...
I have just recently configured and concluded adding a 2950 to the network of a series of 6500 and 4000. When I added a device onto the 2950, it received an IP Address via DHCP and worked well. But when I added an IBM Blade Server onto the 2950, we s...
Hello,A RAS is disconnecting PSTN calls with causes = 0x7F00 and 0xDF00Can someone explain me thoses causes ?All disconnected calls for 0x7F00 are very shorts ones.Here are some SYSlog traces:%MODEM_HIST-3-END_CALL: Mica Modem 1/11 Connect Protocol -...
