The Catalyst3550-24-EMI is connected to Catalyst6509 with trunk, and Catalyst2950G-24 is connected to 3550 with trunk. but in topology of Campus Manager, The 2950G is showed as unconnected. they are individual. What can I do?
The Catalyst3550-24-EMI is connected to Catalyst6509 with trunk, and Catalyst2950G-24 is connected to 3550 with trunk. but in topology of Campus Manager, The 2950G is showed as unconnected. they are individual. What can I do?
Cisco' s position at the access layer has been layer 2, using uplinkfast and backbonefast. Extreme and Foundry are pushing L3 at the edge in their designs for load balancing, QOS and fault tolerance. ( resulting in a more complex network)Has anyone d...
Hi,How to identify root bridge in catalyst 6509 and how to set backbone catalyst 6509 as a root bridge for the network.
hello, how to differentiate between exploring and download netflow of http? Exploring http netflow must take precedence over download http netflow,Because download http netflow occupy too many bandwidth.BRs
Hi ,can anyone know where i can find a TTL table ?i know that inside the LAN the TTL start from 64 and goes down.if the packet have to go across the internet the TTL is 255 and down.broadcast is TTL 1.i need full table, does anyone have it ?thanks ro...
hi,my question:i have a cisco7513 router which is connected to an ibm host over a cip-card.there is the following configuration on the card:..lan TokenRing 7 source-bridge 1127 1 1120 adapter 15 4000.1090.0002 name Geos_Tir and so on.there is a...
from some vlans i cannot ping the virtual ip add of the exchange cluster, but can ping the nic ip add. when i do a "sh ip arp vlan 100" in router-16, i can see the entries for the all ip add, including virtual cluster ip. when i do same in router-15,...
Scenario:T1 coming into an office complex terminating at a Cisco 1751 running IOS Firewall software. Office complex has multiple separate companies with varied and separate internal network segments. Need to share T1 between these disparate network...
I have a 827 ADSL router with the ethernet port.I would like to know if I can set it full duplex. I can't seem to find the proper command that works.Thanks.
Am I right when I say that at today there aren't devices supporting 100 baseFX over single mode fiber ?I saw that there should be an IEEE standard coming out but ....ThanksMarco
Sir, Is it possible to use the command "rate-limit" in cisco 4000,4000M, 4500, 4500M and 4700 series routers, for that which version of IOS is to be used. Will these series routers support the bandwidth restriction using ip. Please send me the report...
Sir,Is it possible to use the command "rate-limit" in cisco 4000,4000M, 4500, 4500M and 4700 series routers, for that which version of IOS is to be used. Will these series routers support the bandwidth restriction using ip. Please send me the report ...
I have two C1720 routers whose Ethernet interfaces are on separate subnets, separated by a PIX FW. One router connects to the Internet, the other connects to a P2P circuit connecting two sites. Each site is configured similarly with two routers (on...
We are needing to have two ISP's in diverse locations. Our main site in dallas currently has an ISP. We need to employ an ISP in our Houston location as well. These two sites are connected via frame relay. We have the basic PIX, DMZ and LAN connec...
hi,my question:i have 2 7513 router which act as dlsw-peer for our ibm-host.i configured 2 hsrp-groups, where for group 1 the 7513(1) and for group 2 the7513(2) is the active one.the two hsrp adresses are 10.18.254.221 and 10.18.254.222.now i want to...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |