Other Network Architecture Subjects

Hi,I have multiple spoke routers with FR to the service provider and on the hub side I am using IMA( atm multiplexing), and isdn as the backup for all these.On both sides of the networks I have voice data coming on vlan 2, which is configured as sup...

I have a WIC 56K 4-wire CSU/DSU installed in a Cisco 1720 router. The CSU/DSU is connect to a Frame-Relay DS0 circuit. The serial interface is configure with the following statements:interface serial 0encapsulation frame-relay IETFservice-module 56K...

Is there a way to generate audit logs on who is accessing CW2000. This is a requirement from our security group to have logs on who is try to login to the CW2000 via their browser. (both successful and unsuccessful attempts) The only thing I have f...

I have a 1720 connected to remote site 3620 through one serial and one BRI.Right now I am using static route, I intend to use OSPF. How do I configure to prevent OSPF bring up the dialer interface? Is there any related document?Thank you.

Hello:I have a series of 3550 switches between a core and edge router that are passing all traffic at Layer 2 (no Layer 3 services enabled on the 3550's). On each of the uplink ports between switches, we have "switchport block multicast" enabled bec...

Correct me if I'm wrong, but dont you have to configure redistribution between different ASs in EIGRP?Ex.: running EIGRP ASs 100 & 200 on two different interfaces(on the same router). Will the routes learned via a neighbor in (EIGRP)AS 200 be passe...

Have a 6506 that decompresses the image (6-3-3.bin). Goes through power up diagnostics and then sits at:>System Power On Diagnostics Complete>Boot image: bootflash:cat6000-sup.6-3-3.binand that is it.set at rommon gives me: ommon 7 > setPS1=rommon ! ...

Hi,I'm trying to configure a 3640 with a 8 port BRI interface card and an Digital Modem interface card. Does anyone know how you can configure the number of start- stop- and databits for incoming analog connections?Kind Regards,Tom

I am thinking of segmenting my switched network of about 200 PCs using VLANS for the different departments. However, I would like to show my boss that the switch is heavily broadcasting in the present configuration. My question is, what is the freque...

I can't seem to find the command that does this? Can anybody point me in the right direction here?Thanks,Diego

I have a customer with 5 existing switchs (WS-C2924C - 22 ports 10/100baseTX and 2 ports 100baseFX) and he recently bought a gigabit switch (WS-C3550-12G - 10 GBIC ports and 2 ports 10/100/1000baseTX) and 4 switches WS-2950SX-24.He wants to use WS-C3...

I have 4 areas of which 1is L2 area i have 3 interfaces (each in diff area ) of the router connected to a nortel sdh equipment from the router i can clns ping the sdh box in all 3 areas but when i do a extended ping and ping clns from another area's...

All,Due to auto-negotiation problem between our Cisco Cat5000 switches and our workstation NIC's, we've hard coded all switch ports to 100/Full. Occasionally, we will have a user plug in a new machine or NIC that is set to 100/Auto. In these cases ...

I have the following static route configuration:my remote router is connected to:loopback:10.178.201.254/3010.178.202.0/24(vlan1)10.178.203.0/24(vlan2)serial0:10.178.222.254/30ISDN0:10.178.222.251/30my central router is connected to:loopback:192.168....

I can't start CNR's (v3.5 and v5.0) DHCP server on HP-UX11i (while need it) AND can on HP-UX 11 (and no need it)Does anybody know is it desteny or there is some to do to fight this problem?