I am seeing the routing table converge on internal (90) routes on the ISL uplink to the switch. This is only changing the uptime on a few routes and not the entire table. (show ip route eigrp)
I am seeing the routing table converge on internal (90) routes on the ISL uplink to the switch. This is only changing the uptime on a few routes and not the entire table. (show ip route eigrp)
Is there any requirement that a home network for mobile nodes must be directly attached to a home agent router? I have assumed that a mobile node on its home network can be reached from a home agent using routing as usual, when the home agent has no ...
We have one 3548 XL Switch in our network that is very sluggish when connecting through telnet and the console. When using the show processes cpu command - the TTY Background process is 26.05%(5sec) 23.01(1min) 23.92 (5min), the overall switch cpu ut...
We have a server located on the web which host a application on port 8888.The clients are on VSAT with private IP ( 10.x.x.x ) and get NATed to 203.x.x.x at the HUB before accessing the server 194.x.x.x. Problem: Due to some reasons in the VSAT we a...
With eigrp variance option, the unequal cost balance can be applied on the 2 serial ports of the router. But unequal cost balance is not needed for other ethernet ports of the router. How to limit it? thanks!
Dear NetPro Team,I would like to know which command displays the native ios equiv. to thehybrid command to check the mbuf / cluster resources.Thanks in advance,Andy
i am deploying a campus network for a client with 50 user workstations ,the client specifically requested a 4003 catalyst switch bundle as the network switch,am not sure the type of access switch or is it hub to use at the access layer,? ps advice
I'm consdiering using Policy routing by source address to do load balancing across 2 routers with an ISP link each. (All traffic goes to router A first) If a packet goes to Router A and policy routed to Router B, what happens if 1. Router B is down b...
This is a question about multicast. I´d like to know if a router configured to be a RP can also have receivers conencted to its interfaces, or the receivers should be at other routers? Also, even if it does not have receivers, being a RP, can I put o...
Has anyone had any experience running Cisco Lan HW in a zero humidity environment?We will be running switches (2- 3600's(?)) inside a Nitrogen purged c1d2 cabinet, and are concerned about static, etc.Also, will a grounded steel cabinet be sufficient ...
I am deciding on a networking architecture to interconnect 16 metro sites and need to decide between a small carrier (MPLS) or a large campus (VLAN).We lease fibre to most sites, but have some 34Mbps microwave and 2Mbps for backup. We require secure ...
Essentially, the title tells it all. After upgrading from 12.0.8 to 12.2.7a, our passwords wouldn't work. Is this because of a different encryption algorithm? We are using the service password-encryption command, and would like to keep it on during o...
what is the difference withe the two commands?modemcap edit [modem-type]modemcap entry [modem-type]
what is difference native vlan between ISL and dot1q ?In dot1q, two switch's trunk port must be same native v lanbutIn ISL, two switch's trunk port is not same native vlan two sentence is true or false? why? plz..thanks.
I just got a couple of replacement 2924's and when I put them into the stack to replace the bad ones and configued them, everything worked except the new ones weren't receiving vtp updates. I have checked and triple checked the vtp settings and every...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |