we have ciscoworks 2000 software installed on NT .. when i run the campus manager the cw2k is giving an error ANI server is not started. I tried to create new ANI data base but still giving me the same error.
we have ciscoworks 2000 software installed on NT .. when i run the campus manager the cw2k is giving an error ANI server is not started. I tried to create new ANI data base but still giving me the same error.
I have a user who has HPOV on 1 box and CW2k on another, the integration for CV was working fine but the IP address of the CW2k box was changed, Network Node Manager was then still launching the the CV app and looking for the old IP addresss in the a...
I have about 100 2950G-48-EI that I would like to manage with RME 3.4 butit does not recognize them as switches but as generic snmp devices. Does any one know if they are being supported in RME 3.4 yet or if there is a patch or anything that will l...
Hi All,Symptom: A few Cisco Catalyst 2950 switches installed into an existing network. All users migrated to the new switches. Most users have no problems with connecting to the "new" network. However, users using 3C905B-TX NICs do not have network c...
my 2500's or 2600's will lose their SAP and Server tables for no apparent reason. they are running 11.3, are there any know bugs that will cause this, I cannot find any.
How do I get the configured duplex status on a c2950?I check the "c2900PortDuplexState". It worked fine on c3500XL Series. (3 = auto duplex).But on c2950 Switches, as soon as the Port is 'up', it gives back the actual duplex state (i.e. 2 = half dupl...
HiI have a hub and spoke network with 16 remote sites. I have implemented frame-relay traffic-shaping on the major serial interface and this has applied shaping to all of the sub-interfaces. I really only wanted to shape 2 of the sub-interfaces and n...
Does the dynamically created entries in the L2 multicast forwarding table, made by IGMP Snooping expire, and if so, what is the interval or maxage? Also how does it work with 'response suppression' in IGMPv2, so that each group member can retain the...
In an installation of LMS 1.1 on Solaris 2.6 i have pulled the actual configs from the routers by "update archive" manually. This will download the running config , if it was changed. But the startup config isn't downloaded into the archive. I always...
Is there a way to make the routing decision based on source address? For example to be able to route a specific source ip address to a specific interface inside the router.
We have Cisco 3640 router with NM/4E module installed on it. This NM/4E is used for providing bandwidth to other subscribers in the same building. Bandwidth is provided in the following way.UTP CAT5E cables are layered between our office and our subs...
A Catalyst 3512XL-EN With IOS 12.0(5.4)WC(1) (C3500XL-C3H2S-M)Currently FastEther 0/7 is jioned into Vlan 30,Directly connected with a PC and the MAC address of the PC's NIC is 00e0.4c3c.5310,the communication is Ok,and then I used commands flowed:35...
I have the following network:Router B Router C(e0: 10.1.1.1/24) (e0: 10.1.1.1/24)(NAT: 11.1.1.1) ...
We have 2 C3600 connected via 2 MB leased Line to one central 3600. In case of a break of the leased lines, the both remote routers should dial 15 b-channels but the don't. One dialed 10 connections, the other one only 13 channels and both tell me in...
I had a problem with loopback int in a 3550-48-EMI, i had created one of them and now i can delete it, i use the no int loop1command in config mode and it doesn´t work. And now i had 3 int loop1 on the switch??? and i can delete none of them. Some ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |