Other Network Architecture Subjects

HI All , I have a situtation here , IM trying to dial in from a remote site with a cisco 801 into a cisco 2610 which has 4 port modular slot.But am facint typical problems which IM sure some one would have comeaccross , but if some one could kindly ...

I am currently running Catalyst 3548XL in all my closets. They are all run at 10/half because the building a little old there is still a lot of CAT 3. Our art department has been approved to be upgraded to all CAT 6. So I would like to bump all th...

We are currrently trying to connect a Cisco 3620 router to a T-1 line. The connection from the T-1 line is an RJ-48. We need to set up a CSU/DSU to manage the clocking of the line. In order to lower the cost of installation we would like to purcha...

I would like to perform an l2trace from one switch vlan 2 across several switches (msfc installed), different VTP management domains to a workstation in vlan12. I get the message vlan must be specified. Has anyone tried this command l2trace? I feel I...

Has anyone implemented DFM and configured it to work w/ Telalert, or other similar notification utility? It sounds like the primary way of accomplishing notifications is via the mail notifier gateway but that seems to offer limited flexibility. Tks...

Hi guys,I am have a switch cisco WS-C2924C-XL connected to a switch planet FNSW-1600S via 2 fiber optic, in the Fast Ethernet 0/23 I am having : FastEthernet0/23 is up, line protocol is up Hardware is Fast Ethernet, address is 0050.806f.2f99 (bia 0...

Hi, Anyone knows how to transparently bridge two spokes in Frame-relay network if both spokes are connected to a HUB router using a single multipoint interface. Thanksamdcent

Could I use wilcards in the mac address for port secure? For exemple, if the first 32 bits where the same, could I let the switch filter only on the first 32 bits, no matter what the next 32 bits were?

Hi,I've got this scenario:[R1]---ethernet---[Switch/ATM]----ATM------[Cisco7206vxr]The Switch is a Nortel 8610, and it's bridging the ethernet port with the PVC within the ATM link to the 7206vxr.I've configured the ethernet of R1 with IP 10.10.20.2,...

I have a Cisco 2509 running 11.3(5) IOS with the octal cable configured for PPP dial-up for remote users. Works great except that I can get connect speeds only up to 26k. I take the modems off the cisco and put them on an ascend box and I get 54k c...

We have a 6509 with dual sup 1a and MSFC/PFC 6.3(6)installed. I have a server that was placed on one VLAN and only 3 other VLANs including my workstation is on can ftp to this server quickly. Workstations on other VLANs have slow performance to conne...

I have a 2514 router connected to two ethernet subnets and a serial connected to a frame relay (internet). A real text book example for a small office. E0 is the internal network private addressing and E1 is the subnet with the public addresses.. ...

Hi,i would like to configure the VTY lines of a router so2 users can telnet but with different password.So i changed the configuration i had"line vty 0 4password ..........login"by applyingno line vty 0 4line vty 0password....loginline vty 1password...

I have a Catalyst 5500 with an RSM with a specific routing need.VLAN 200 - Our ISP provider (Y.Y.Y.Y)VLAN 202 - External Network (X.X.X.X)VLAN 201 - Internal Network (10.0.0.0)VLANS 10-15 - Various other Internal Networks (192.168.X.X)Between our ext...

Hi,we intend to connect two locations with a 34Mbit HSSI-link. On the remote side there are about 140 users. What kind of router is the best to realize it ?What must be taken into consideration ?I would be grateful for a quick responseMany thanksNorb...