Hi, I just would like to confirm that the IP addresses outlined below for RouterA 'neighbor' command is wrong. Please confirm I am not missing anything.RouterA RouterBAS 65111 ...
Hi, I just would like to confirm that the IP addresses outlined below for RouterA 'neighbor' command is wrong. Please confirm I am not missing anything.RouterA RouterBAS 65111 ...
Question regarding slot use...I have a 6513 chassis with (4) 48 port gig ethernet RJ45 interface cards in slots 10-13 and a 48 port SFP card in slot 9. These are the only slots that these fabric enabled cards will power up in. I am running a sup720 i...
i am really new to 4500 and 6500 series switches.....just wondering whats is the use of MFSC module and supervisor engine module on these switches and whats the difference btw them....thanks in advance
I have a 1811w which I need to get a print job originating from a external static address to an internal static address communication is occuring on port 515 from the outside. I've created a nat port forward to accomplish this as well as made entries...
I have a new ISR 2811 with this IOS c2800nm-spservicesk9-mz.124-3e.bin. I want to be able to configure a Easy VPN Remote Server using SMD. To which versio do I have to upgrade to have this feature on my ISR.Thanks a lot for your time
Hello,My network atthe moment is set up as:WAN, with three sitesSite 1Site 2Site 3Site 1 is behind a non-Cisco firewall, which is connected to the internet via a Frame Relay link (using a Cisco 1721 router). We host a number of servers on the Interna...
FRW-trunk#sh verCisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC3b, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Fri 15-Feb-02 10:51 by antoninoImage text-base...
hello netpro:I have a simple question, how to modify the mtu on 3550 ,the version is c3550-i5q3l2-mz.121-20.EA1, thank you
what do these tell other switches and what are they used for ?
Is there a way around this? I have to basically assign an IP/subnet just for failover for each interface I want to use as vlans.I have 2 pix fw in lan based failover mode.5 physical interfaces. state (failover)indsideoutsidedmzdmz2I have 4 vlans,...
I've discovered the feature 'Using 31-Bit Prefixes on IPv4 Point-to-Point Links' and I'm interested in implementing it on a point-to-point uplink network that terminates on one end to a Catalyst 3750 routed FastEthernet port ("no switchport").I can e...
We have CC Contact Center using Cisco Voice over IP platform, the historical report is one day behind.See the attachment please, synchronization on Wednesday but the APP and DB on Tuesday.http://img141.imageshack.us/img141/9383/voiphistoricalreportoa...
Hi all, when I do sh spanning tree on my switch it gives me the output shown below, my question is, what is the root and bridge id ? is that the actual root switches info, and the bridge id is its own info ?LAN0001 Spanning tree enabled protocol iee...
what are these ?
We are having difficulty getting IBM Broadcom NetXtreme Gigabit Ethernet cards (driver ver. 9.56.0) to negotiate 1000/full with 4500 and 6500 Cats. Switch info:6509, s72033-jk9sv-mz.122-18.SXD6, X6748-GE-TX4506, cat4500-ipbasek9-mz.122-25.SG, 4548-GB...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |