How many possible networks can i get out of a /24 using vlsm ? would it be 2 x /25 + 2 x /26 and so on, can anyone tell me by doing a listthanks a millionthanks
How many possible networks can i get out of a /24 using vlsm ? would it be 2 x /25 + 2 x /26 and so on, can anyone tell me by doing a listthanks a millionthanks
Hi everyone, I've a question for you guys:Please check this topology: http://www.cisco.com/warp/public/473/84d.gifI've read that you must enable loop guard on every nondesignated port (root and alternate ports) to prevent unidirectional related loops...
HiI am trying to setup an int Multilink1====================================== interface Multilink1 description MLPPP no ip address no ip redirects no ip mroute-cache peer default ip address 172.29.194.18 no keepalive ppp ipcp dns 172.25.72.1 172.25....
how would i load balance to 2 different isp's, would I just use ip cef, and use per destination load balancing ?thanks
I don't think this is a Cisco problem. When I try to access our school homepage from a 192.168.x.x network it is very slow to load. When I access the page from a 172.20.X.X network or registered subnet it works fine. It also works from the Internet. ...
To prevent interface status being error-disable, is it valid way to configure "port debounce time" on interfaces ? The customer use Cat6500 with the following modules:- WS-X6K-SUP2-2GE with Cat OS 7.2(2) - WS-X6408A-GBIC In the CatOS case, when the p...
Hi I've one router 1721 and your s0 is x.x.x.6/30, the serial of telco is x.x.x.5/30, the fast of my router is y.y.y.y/26. The encapsulation ppp was configured, my router ping the router broadband telco and internet, the broadband ping my router ...
Is it possible to block access from one host to another host (in one direction only), both in the same vlan.I read about acl blocking using mac id and tried it too, but could not succed.the switch used is 6509
hi allCan anyone tell me how come my switch knows only to issue my dhcp pool to the relevant vlan, the vlan and dhcp pool are are the same subnet, but what if I didnt have a vlan in that subnet, would it not issue them ?
HelloI have connected a router 2821, equipped with two gigabit ethernet ports, each one to two different Catalyst.In order to provide redundancy to its connectivity i configured Integrated IRB at the 2821:Both ethernet ports are assigned to bridge-gr...
Hi,I'm using Stom control option on other switches like 3550 or 3750, with a level of 65.00 which I think means 65%. How can I do the same on Catalyst 3500XL?I know that is switchport storm-control, but what value then?Jorge
Hello! We have cat3550 12.1(19)EA1a and we want to setup VRF in next scheme: cat3550------(inside)PIX(dmz)----r2600 ------------tunnel1------- r2600 is a exit point of all tunnels and is a point of connection VRF and global routing. There are two sub...
Hi All, I'm about to purchase an 1841 ISR with a HWIC-4ESW (4port switch). On each of the two built in F/E ports i'm going to put a DSL link with static IPs from different ISPs. Can I set up F/E 1 to perform backup/load balancing for F/E 0? Will basi...
If I confiured the port like this " switchport trunk native vlan 10 switchport trunk allowed vlan 11,12"does the vlan 10 allowed passing ? or it still need add vlan 10 to the allowed vlan list like " switchport trunk native vlan 10 switchport trunk ...
I have a L3 switch with several vlan interfaces. I want to add another vlan interface that is restricted (isolated) from the other vlans. What would be the best way to go about doing this? Should I create an extended ACL and then apply it to the V...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |