Hi, Can TCL scripts be used on SDWAN devices such as ASRs, vEdge or CSRs? I would like to write a script that checks for a certain condition with BFD and reload if required. Can it be templated as well? Brad
Forum Posts
Resolved! I want to make multi vla in wlc
HiNow I have a project in Packet TracerI Want to make multi vlan on WLCSo that every vlan have a different ip range.I have researched and used the method through the interfaces in WLC but I feel that I have some errors in setting the interface by ent...
I am using the PWR-C1-715WAC-p in the 9300 switches. Can i supply this PS with 240 VAC line to line or is it rated for 240VAC line to neutral? Which power chord should I use for 240VAC Line to lin
I'm need to connect to the Console port of an EX60. Documentation mentions a "special cable" but I have Cisco Serial to RJ45 console cable kicking around and am wondering if anyone knows if that would work or if I need to make the special RS232 to TT...
Hello All, I was troubleshooting webex slowness issue for a client and we observe the following. 1-When i was sharing my desktop screen, each user BW consumption was 1.5Mbps they provided this info from the windows task manager Network tab the Networ...
Hello group, I need some advices/help on setup. I need to monitor the ping latency value on a destination/host.In fact, I need to ping a destination IP, based on the latency result, if the latency of the ping(or round trip maybe) is more than lets sa...
Resolved! WIC and 'speed' on 2951
Hi all, Best wishes for the new year, may it be safe and outdoors again! For a Cisco 2951 I have a speed issue. The chassis should be able to put 1Gbs through and it does so on the G0/0-G0/2 ports. However teh WIC cards do not go over 250+Mb.. And i ...
Looking for some guidance around the following setup: We have two Cisco NGFW 2210 (running 6.6), and also have two ISPs (Comcast and AT&T). The HA pair are being managed by FDM (with no intentions of using FMC). I have not seen any documentation t...
Hi, everyone, I'm playing around with Packet Tracer 7.3.1 and a switch 3560-24PS and sticky configuration.I have a scenario where maximum allowed addresses is 2 and this is done by means of a hub.One of them is configured manually with(config-if)swit...
Hi Guys,I'm following lab instructions in this version of PT. I don't think I can say too much about the lab here as its paid material. Anyway, please see the below image. I'm experiencing an issue getting the image of the webcam view to display at a...
Hi everyone,I was wondering if Cisco offers any network and security design and architectural designs and drawing for best practices specifically for shared coworking environments like wework. I would presume that it would be a slightly altered camp...
Can someone explain to me the difference between a Default Gateway and Gateway of Last Resort?
I have Cisco ASA 5585-X with SSP-60 running in HA (Active-Standby). I would like to configure failover virtual mac address to avoid arp issue during secondary to primary failover. (Its Cisco best practice to use virtual mac). In my case i have bunch ...
Dear all,i do have 3 2600 series, one 1750 and one 1650 routers for my lab experiments. all of them having WIC 2 T installed. other specifications are usual. one ethernet, one aux, console ports.how can i connect to all of them, using a single te...
Hi experts!I run sh int ethx/x command to see port speed whether it is 1 gig or 10 gig. But i confused because it said "Hardware: 1000/10000 Ethernet" but it also said "full-duplex, 1000 Mb/s, media type is 1G". So it is 1 gig or 10 gig? The interfac...
