There used to be a tool Cisco had to help converting configuraitons from hybrid to native.Does it still exist or do you have to do everything manually?
There used to be a tool Cisco had to help converting configuraitons from hybrid to native.Does it still exist or do you have to do everything manually?
I have a 1720 with a WIC (T1) Serial0 interface and a FastEthernet0 Interface currently performing NAT and routing several public IP's to internal servers.I need to know how to properly setup a full bridge between the ISP (T1) and the Ethernet interf...
This EtherChannel config is for the same channel group 1:interface Port-channel1 description to 6509-Core-A P1 ip address x.x.x.x y.y.y.y ip route-cache flow ! interface GigabitEthernet1/1 description to 6509-Core-A T1/1 (P1) no ip address ip route-c...
Hi I've seen questions like this before, but never seen a satisfactory answer... I can't find any good documentation anywhere about this command.If you run it, you get tabular output of some statistics - with no headers to the columns.The closest thi...
The topology is simple. Three 3550 switches as the backbone tied together using spanning-tree layer 2 wire speed switching. Very simple stuff there. Introduce 3745 access routers, one attached to each 3550, each loaded with 16port ESW, 1 GigE GBic...
- Sho proc on 4000 shows 20% steady utilization. and the following two taking up most of this util. What could be wrong. I donot see any error messages in the log:25 19693619442955991267 666 15.13% 14.19% 14.54% 0 Cat4k Mgmt HiPri 26 6543...
Folks, Has someone configured one of their core 6500 switches in HSRP mode as DHCP server for the phones. We tried to do it with little success.ip dhcp excluded-address 10.2.12.1 10.2.12.150ip dhcp excluded-address 10.2.13.1 10.2.13.150ip dhcp ...
Hi pls look at attached diagram for reference. Router A is active, Router B is standby. Question is what happens when fibre link 1 (between switch A & B)fails but fibre link 2 (between switch C&D) remains active - which of the two router will be acti...
I have a problem with my Cisco Router of the 800 series (Cisco 827) - it its not possible to have access (ping) to the PC behind the Router, on which a mailserver is installed.I want to have access from an outside PC on the www to this mailserver mac...
Hi,has anybody an explanation and solution for this problem:the network consits of 2 Cisco6513 as CORE and several 3Com Switches 4300 as access switches. There are 4 VLAN´s configured - therefore a trunking configuration (and 3Com´s resilient link). ...
I am using my 3620 instead of a netgear cable router connected to cablevision. 1) How can I see when the router dhcp lease ends so I can see if it gets another address? I have seen on past posts that there were problems with this issue. I am usin...
HiI need to send some traffic to an external L2 device, and then get it back, to the same router.I planned to use PRB, to set the outgoing interface, and the next-hop as the IP address of the incoming interface, from the same router.Is that possible?...
Hi,I am planning to run HSRP and BGP on two routers. The two routers are connected to the same LAN. And each router has an ethernet type of WAN connection (some sort of DSL network) to the ISP. With HSRP, one router will be active and the other will ...
Hello,I'd like to know if we change a vtp client switch from VTP domain "a" to vtp domain "b" (VTP domain "b" currently not existing) if he will keep his vlan database and then can be turne to vtp server for domain "b" and propagating the vtp domain ...
I am running 12(3)13 on my 3620 router. The only options to the clock command are summer-time and time-zone. I want to set the system clock and if I type clock set, I get an invalid response.Any clues?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |