This Nexus seems to have different commands and the BGP is not coming up. I don't show any neighbors or even like it is trying to come up. Below is some information about the Nexus and the config SoftwareBIOS: version 08.32NXOS: version 7.0(3)I4...
Hi,We have a router that on one side connects to the backbone area and has an nssa area on the other side:CORE -- > Area 0 <-- OUR ROUTER --> Area 123 <-- DOWNSTREAM ROUTERWe have the command "area 123 nssa no-summary" added to the router OSPF config...
Hello,Should the mentioned routers be powered off when inserting/removing the Cellular Pluggable Interface Module (PIM) during SIM install? I'm reading this document, but I cannot find anything related:https://www.cisco.com/c/en/us/td/docs/routers/io...
When u join to wifi network we want to open 192.168.8.2:8000 but nothing (this is CUCM).They open only 192.168.8.2:80 and withouth port Cisco Gui for routerRoutingRouter sh run:Routin!interface GigabitEthernet0/0/0ip address 192.168.8.2 255.255.255....
Hello,I'm trying to establish OSPF adjacency between a Nexus9K and an ASA and it is not happening.Hardware: Nexus 93180YC - Cisco Firepower 4115 with ASA OS.On the Nexus, connection in INIT/DROTHER state, the ASA does not show anything.I have tried t...
I'm not sure what the Cisco Secure Firewall 3100 Series commands are.When you issue the command show interface or show running-configCan I check the command just like Cisco firepower and other Cisco routers and switches?
HelloI'm asking because I have a question while studying Multisite.Is there a way to configure BGW not to use Multisite, but not to affect the VTEP scale, which is the advantage of Multisite?
Above is the Client requirement R1 is local router and R2 is remote router. 1) Clients want to separate data traffic and management traffic via VRF in local router and pass it over single MPLS link via separate ipsec data and management tunnel to re...
Hello, I am currently learning about the Cisco tracer packetsmy problem is that when watching the videos provided and going step by step with the instructor, I received a problem where I can't connect the wireless router/ home wireless router to the ...
hi guys.i have a network with below topologyi have two servers that are accessable in my 2811 router and i have a two client with frameware that only support setting ipv4 adderess and doesnt support setting the ip default gateway . the clients connec...
Below is the client requirement for that I have prepared proposed solution diagram in attached where both data and management vrf ingress and egress through same MPLS ISP by static route pointing to the next-hop IP addresses that are reachable throug...
Greetings & Salutations to the Cisco Community! I have been working with Cisco Routers, Switches, and Security Appliances over the past 25 or so years, however, this is my first time posting here! I am working on selecting a branch office router for ...
Hi Community, I am facing some issues on the route learning via EBGP.I like to receive only specific prefixes from PE, e.g. 10.61.128.0/22I like to advertise only specific prefixes to PE, e.g. 10.50.120./22 #Adverstise to VENDORip prefix-list vendor-...
Hi We have a connection from on-premises to Azure via the ExpressRoute virtual router, with BFD enabled. The BFD interval is set to 1000ms on the on-premises side and 300ms on the Azure side. However, the BGP session is frequently resetting due to BF...
I am working with the Cisco Catalyst IR1101 router, which run the ir1101-universalk9.17.12.04 firmware. I have been trying to configure a site to site tunnel. If I start the router up with the default factory configuration and add these lines 1 by 1:...
