Background: In our production environment we have a C9500-40X acting as a layer 3 switch with many VLANs and layer 2 switches connected. The layer 2 switches range from 3560 at the low end all the way up to 9300 mgig switches. We have 3750 and 3850...
Forum Posts
Hi , Is there anyway to delete the service providers from IWAN APP after clicking on save and continue.Tried clicking on previous and tried to delete but its not allowing.
Enable password is now unknown. I am thinking the running-config was modified incorrectly when adding acs configuration. I have never done a password recovery before. What is the estimated downtime? is the first option listed the best? https://www....
Hi the following is an output of my int briefGi0/0/0.12 10.0.0.1 YES manual up upGi0/0/1.12 10.20.0.1 YES manual up up and the following is my ip route on the vrf where the above interfaces are forwarding S* 0.0.0.0/0 [1/0] via 10.20.0.2 10.0.0.0/8 i...
Hello, My topology :My configuration : R1 : BOX1#sh runBuilding configuration...Current configuration : 2022 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname BOX1!bo...
Hello,because my last question was a bit of missunderstanding I created a new one. I have an Cisco SG350-20 Switch, which is a Layer 3 switch. To this switch are connected a Notebook A with the IP 192.168.3.1 which should simmulate a server (just nee...
Resolved! NTP-Server over VRRP
Hi all, I need to find a solution for two routers which will act as ntp-servers. Can I configure them with VRRP to share an virtual IP or is there a better way? Thanks in advance
Resolved! BGP sessions monitoring.
Hi,i have 4 BGP peers (ISP) connected to my WAN routers.I want to monitor in real time how many active routes i received from each of the peers.I was unable to find the coresponding MIB.Do you have some better scenarios/software to perform BGP monito...
Resolved! IS-IS route flapping
RP/0/RSP0/CPU0:PE1# sho route 10.x.47.25Fri Feb 2 12:00:28.308 BKKRouting entry for 10.x.47.25/32 Known via "isis 47", distance 114, metric 20, type level-2 Installed Feb 2 11:57:33.751 for 00:02:54 => it's never more than 5 minutes Routing Desc...
Please Could anyone explain to me in very simplistic terms, what the use of stub routing is. Most of the texts on this matter just jump into configuring the feature. Here is my definition: Stub: Main use: for resource utilization on specific router...
Hello, Does anyone have any experience using the default-originate route-map to a neighbor and having the route-map match a community? I have a design specific requirement to advertise and originate a default route to a specific neighbor only and...
Resolved! Lab: Routers multi-area
Hi, Guys, I'm trying to build this lab but I got really confused. I had to do it and do it again and I cannot.any help and explanation would be much appreciated. Thanks a lot in advance.
Hi, I am reading a CCIE book and found a topic on Distance Vector Routing Protocol (as RIP and Eigrp) migration and getting stuck to understand the real logic behind the seen "A learned route will be advertised further only if the router has placed t...
Hi everyone!! I’m working on a class project that needs a dedicated fiber line between DC and ATL. The routing protocol is RIP v2. It needs to have banner motd on all switches and routers, interface description on all interfaces, all passwords are su...
Hi,***Manufacturer: CiscoType: Power SupplyModel: PWR-60 W-AC***I would like to know the type of input plug the router in question is 12 V 5 A 5.5 mm 2.5 mm 2.1 mm or ...thank you,ITVC
