I have the following topology : I have an ethernet connection to another route out the opposite-side port of my LAN where I have the two vlans configured (VLAN, 10 (Marketing) and 20 (Sales)) Before I set up the following ACL and the following c...
Hi All, We have 2 x 5512-x ASAs, one in our LA location and one in our PA location. The one in LA (let's call it ASA01) is in production and I have the tunnel configured. The one in PA (ASA02), is set up but it sits behind a Netgear router. From th...
Hi All, I have four routers in the same BGP AS which redistribute their BGP routes into EIGRP. There are route-maps to prefer one router over another for particular subnets and that all works fine when the routers are turned on in the right order. Ho...
Hi everybody. I have a Cisco 2811 router with one Fastethernet L3 port in trunk mode, with sub interfaces, and a switch connected at the end with Vlans set up in another room. I had planned to use the gigabit port on a NM-ESW-16 module to creat...
Hello, I am migrating from a 6513 core/dist switch to a 6807XL. The 6513 and 6807 are currently connected via a layer 2 port-channel trunk link. The SVIs and VLANs have been configured on the 6807, but are currently shutdown. Static routes and A...
I am having trouble setting up DMVPN in a virtual network in GNS3 for a proof of concept before putting in on a live network. I can get the static tunnels from the spokes to the hubs to come up but I cannot get traffic to pass though the tunnels. I c...
Hello,i have a WS-C3750G-12S with IOS Ver. 12.2(35)SE5, IPBASE.In its config it has the command "ip host-routing" which i tried to delete several times without success.A "no ip host-routing" command gives no error but it does not do what i think it s...
Good evening. I am working on a bgp routing issue and decided that using the backdoor switch to make my router prefer my eigrp route over bgp would make routing this particular set of networks more efficient. So, here is the problem: I am advertis...
Hi Friends,i have 1001 ASR which boots up ok but shows a warning "filesystem is not clean" and thereafter the image is validated well, it shows up the following two messages and just goes idle from there.%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0):...
Hello All,After upgrading a Cisco ASR 1001 using sub packages from XE 03.07.00b.S too XE 03.09.01.S (following the instructions detailed in the Cisco documentation but without redundant OS/RP) the device is continually reboots with the following erro...
Hi All Can anyone tell me how most ISPs keep customers separate on there networks, do they just use MP-BGP with VRF? How do all the routes map into the labels to keep them separate?
I have Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(2)E3, RELEASE SOFTWARE (fc3) and I created an access-list to prevent my network to access other 4-networks, the 4-networks I can not access the SWs. when I tried to conf...
Hello cisco community. me and my classmates are doing an assigment made by our teacher. we have to make a small network by 3 pc's 1 router 1 switch and 1 wireless accesspoint. some of the requirements is to setup source NAT, DNS forwarding, SSH and a...
i have configured BDI interface on ASR Router (ex BDI 100) And given it Test IP 10.1.1.1/24 and it is UP and server with IP 10.1.1.2/24 can Ping BDI interfacebut when we shutdown one of Sw interface ( Ex: SW-01 Port Fa0/1 ) , Ping fails .It seems tha...
Hi, If suddenly license expired, will router unable to be configured with BFD? Originally, router is configured using BFD. Then, noticed that router down and unreachable remotely. But later when I checked the syslog, there was no log that indicate ...
