Hello, I'm hoping someone can help with a strange problem I'm having. It seems like a routing and/or NAT problem, but I'm not sure what is causing it. I just setup a new network in my home this week with a new Cisco ASA 5506-X and Catalyst 3650 24-...
Forum Posts
Hi, I configured Ipsec tunnel between two endpoints with Virtual-Template interface at one end. Tunnel is established successfully between both routers with Tunnel1 at one end and Virtual-Access1 at other end. I am unable to add static route with ex...
Hello everybody, I came into realization that our deployment of extending L2 with L2TPv3 inside IPSec does not work with 1000v cloud services router. Background of the deployment: Purpose of the current architecture and restrictions - extending L...
Resolved! DMVPN + EIGRP neighbor not found
HelloMoving from LAB to production and I cannot get the HUB router to participate in EIGRP. I see in the logs neighbor not found (10.1.2.192) which is the spoke's tunnel interface.HUB:interface Tunnel1 ip address 10.1.2.1 255.255.255.0 no ip redirec...
This may be an issue with packet tracer itself. I probably just need to start a new "template". as shown on the right, my router has a dhcp pool that was created under the 192.168.0.0 network and it was working fine earlier but now one of my hos...
HI , Can you please help me whether Cisco Catalyst 2960XR-24TD-I supports PBR, RIPv2, OSPFv2,RIPng, OSPFv3IPV6 First hop security, Static routing and also Dual stack mode to run both IPv4 & IPv6 RIP and RIPng.. If yes then what will be the part nu...
Hi, I'm trying to use one 877 router as an ADSL gateway, just supplying a WAN connection to a backend 877 router that needs to speak to my ISR back at HQ in order to form a VPN tunnel. Normally we have these directly connected but I need to have a s...
Resolved! Cat3750 copy run start error
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be rec...
Hi! I want to pass muticast traffic from WAN to VLAN interface but it's not working. I'm sure that is missing something but I'm not seeing what. I appreciate your help. Thanks! Router#sh ip int bri Interface IP-Address OK? Met...
Hi, I have 2 ISP connections, one with 10 Mbps and another 10 Mbps. I want two links to work together simultaneously two 10 Mbps link in one Nat network of 192.168.1.0/24 I have a Cisco router 2911(3 Interfaces only) in inside how to achieve this li...
We have a WAN that is setup with BGP, DMVPN, and EIGRP. 10 sites all connect to the service provider via BGP and to each other via DMVPN with EIGRP running on top. We're experiencing an issue where any egress traffic from Site A to any other Site is ...
I need to create a virtual interface on a router for an ISP modem to provide internet access. The ISP has provided the IP, mask, and gateway for the modem. However, what will the IP address need to be for the interface on the router? Do I just cho...
Resolved! line vty authentication question
Hello - I'm wondering if I'll be able to access a pre-configured switch after deployment without TACACS credentials. The line that reads login authentication *ACS username" (I've hidden the actual username) will this require TACACS? Or will the acc...
Most particular request! There a site to site VPN from a subnet GWB 10.0.4.0 to GWA 192.168.1.0 That works plus internet all good. Now, we connect an Access Point to the Cisco 886 and put a different private ip as 192.168.2.0 in Vlan10. Wifi works...
Resolved! ARP Table with Internet Addresses in it?
Hello All, I believe the answer to my question was asked and answered here. But, I would just like to verify if the same thing applies to me. There are basically 2 interfaces of importance. Serial0/1/0:0 is for our MPLS private link and Gi0/0/0 i...
