I have a 1841 Router with IOS C1841-ADVSECURITYK9-M), Version 15.1(1)T. How can i configure Anyconect ? Is this possible wiht this version or should i have a license for that? Thanks
I have a 1841 Router with IOS C1841-ADVSECURITYK9-M), Version 15.1(1)T. How can i configure Anyconect ? Is this possible wiht this version or should i have a license for that? Thanks
Hello Team, One of the client asking to use our side public ip for local encryption domain and currently we are using private series only, please check below configuration. !crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isa...
Hi, We have a very specific requirement with IP SLA. Based on a tracking, we need to failover to alternate routing path and stay there forever untill some user intervenes to failback to original route. Could you please advise the tweak for such setu...
Heya I've got a 887va router configured and working with static NAT mappings working ok for the few mapping we had We are adding VoIP to our network enviorment and need to map a large number of ports, approx 510 ports, easily so discided on trying ...
Hi all, I have seen the videos and guides how to setup a simple site to site vpn between 2 asa's using asdm and followed carefully all the steps, can i have some help please why vpn is not coming up ? this is my topology, and by using permit ip any a...
Hi all, I have the following test topology for transit AS configuration. I cannot ping loopback IP addresses of ISP test 1 and test 2 from any of my internal routers as well as test 1 cannot reach to test 2. pr1_bl#sho ip bgp rib-failure Netwo...
Hi I have Cisco 881 router. Need to configure BSNL Leased Line. I have WAN IP 172.24.X.X/30 and Public IP 117.242.X.X/28. Along with this I wish to use private IP 192.168.0.0/24. Please suggest with configuration details.
Hi All, I am building my own interpretation of the IPv6 topology used in the CCNP TSHOOT exam in my basement for practice purposes. This topology is made public by Cisco, and the configurations are my interpretation, NOT a copy of what they use, so ...
sup: WS-X45-SUP7-E module: WS-X4712-SFP+E: Cisco Catalyst 4500E Series 12-Port 10GbE (SFP+) let me know what version needed to run ws-x4712-sfp+module with sup ws-x45-sup7-e. thanks in advance.
Hi Please the attached Diagram and Router NAT Configuration. I'm just curious about outside NAT concept. Internal network is 10.100.10.0/24 and remote site 10.16.10.0/24. I would like to do NAT either Source address and Destination address on Router ...
Hi Anyone can explain "Cisco endpoints" ? is this special term or ... ? Thank you
Hi All, Can anyone help me to understand the issue what is happening here for below traceroute issue ? I am getting same hop IP address in hop 2 and 4. As from the trace report it seems 2 routers are showing each other as next hop for same destinatio...
Please suggest me the router model number which flow the below criteria 1.WAN service Throughput: 2 Gbps minimum 2. Backplane Capacity: minimum 9.5 Gbps 3. DRAM :Min. 16 GB 4.Flash Memory : Min. 16 GB (installed) Max 30 GB 5.Upgradable Interfaces ...
I do not have internet on my 2960G with my vlan's does anyone know how to solve this?
I have a 5020 setup with inter-vlan and am able to ping devices across the vlans. I am also able to ping the outside 8.8.8.8 from the 5020. If I point an end device to use the 5020 for the gateway it can't ping past the 5020. There is a firewall conn...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
10 | |
10 | |
9 | |
3 | |
2 |