Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

ASR1002 Errors: Failed to load driver contdev

We have an ASR1002 running the following: OS: Cisco IOS XE Software, Version 03.16.04b.S - Extended Support ReleaseCisco IOS Software, ASR1000 Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.5(3)S4b, RELEASE SOFTWARE (fc1) ROMMON: 0         0...

JohnKerns by • Level 4
  • 5457 Views
  • 8 replies
  • 0 Helpful votes

блокируется интерфейс, если пропадает VPN

1) есть несколько роутеров 29012) поднят Dynamic Multipoint VPN 3) тушу тунель на споках руками (командой shutdown в интерфейсе туннеля) - в бранч офисе доступ к остальным сегментам корпоративной сети пропадает, но интернет работает 4) на хабе меняю ...

Resolved! how to solve this acl issue ?

I want to block 192.168.3.0 network from reaching network 192.168.2.129  of Router 3 I tried below acl on R3  access-list 51 deny 192.168.3.0 0.0.0.255 access-list 51 permit any Interface eth1/1  =ip access-group 51 in still  192.168.3.0 can rea...

jordan-jj by • Level 1
  • 1785 Views
  • 10 replies
  • 0 Helpful votes

Resolved! Implementing Two ISP Public IP Blocks

Client has moved ISPs and has been provided two public IP blocks, a /29 "WAN block" and a /28 "LAN block".  We initially utilized the single WAN IP provided by the ISP /29 "WAN block", but we now need to utilize additional public addresses made avail...

axiollc by • Level 1
  • 3509 Views
  • 14 replies
  • 0 Helpful votes

WAN Load balance using static routes

Dears,  I have Cisco routers with 4 lte SIMs,  I want to do load balance so I do the following  ip route 0.0.0.0 0.0.0.0 cellul 0/0/0 ip route 0.0.0.0 0.0.0.0 cellul 0/1/0 ip route 0.0.0.0 0.0.0.0 cellul 0/2/0 ip route 0.0.0.0 0.0.0.0 cellul 0/3/0  ...

not able to telnet to pppoe ip address from remote network

hi every one, I have a 1941 router with gig 0/0 configured to act as pppoe wan, through which dialer 1 interface connects to the isp. The pppoe connection is up and and has an IP address (gained through negotiation). The problem is that I can't telne...

by • Not applicable
  • 1488 Views
  • 13 replies
  • 0 Helpful votes

Resolved! WAN cabling and protocols

Hi All, I have been reading WAN technologies for the last month and got various questions, where I would deeply appreciate your help. 1- In leased lines technology, it can be used to connect into two sites or connect to the Internet. When connectin...

a.azab by • Level 1
  • 551 Views
  • 3 replies
  • 0 Helpful votes

OTV configuration on CSR1000v

I am trying to configure OTV on the CSR1000v platform but all the examples I have come across on the googles is two CSR's connected back to back and have their connecting interfaces in the same subnet. But I am looking for how to do this when my data...

Resolved! telnet <servername> 80

Hi All, I am having trouble to go out from port 80 in my router. With ACL:public-interface-in, I cannot do telnet www.google.com 80. When I remove ACL, it is working. What else am I missing here ? Thank you in advance, interface GigabitEthernet0/0 i...

S Prvr by • Level 1
  • 1323 Views
  • 2 replies
  • 0 Helpful votes
View All
Unanswered Topics
View All
Review Cisco Networking for a $25 gift card