Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

Resolved! Flexible Netflow v9 on 4331

This is my first, in what may be a series of netflow questions. I just received a couple of ISR 4331 routers.  We are going to use these as internet routers for our company. I would like to set up Flexible Netflow v9 with NBAR support to send to our ...

amercer00 by • Level 5
  • 1037 Views
  • 1 replies
  • 0 Helpful votes

Cisco ISA550w Advanced NAT (Hairpinning)

I had my Cisco ISA550w configured with Advanced NAT so that we could access an internally hosted webserver using the external domain name. I (like a dummy) made some changes to the WAN interfaces and all the NAT configurations went byby. I know can n...

About "multicast"

Hello all,I just configured whole my network settings.But one issue tease me.The one which is teasing me is about "multicast". Network design is attachment I uploaded. As you can see the picture, you can find 2 side.One is "192.168.0.x/24 side".Anoth...

Resolved! Use 2x MEM-3900-2GB on Cisco 3925

hi all, we usually order and use 2x MEM-3900-1GB but our vendor sent 2x MEM-3900-2GB instead for our 3925 router/ we would like to use the 2x GB DRAM sticks and was wondering if it's possible? per link below, it said 4 GB will be available in future ...

QOS question

I need to make sure TEMP only get 90 meg of the circuit no more. I thought this would do it however netflows shows ti goes up to 150 meg. I have  a 150 meg circuit class-map match-all TEMP match access-group name TEMP policy-map QOS class IMPORTANT s...

jfeo by • Level 1
  • 549 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Policy based static Natting - HELP

Hi All We have a requirement wherby we have device which needs to be accessable from the outside, so we have done a 1 to 1 static nat from our dialler interface using port number, this works fine. However the same router have a site to site vpn conne...

WAN load balancing question

Hello All, I need some help on below.- ISP-1 provided two routers (R1 and R2), each router connect to a different internet circuit (ISP-1 and ISP-2 circuits)- Locally have a customer router (R3)- Locally have a public DMZ (203.xxx.xxx.xxx/24) Require...

Resolved! EIGRP Distribute List

Hi If I have a router, and I want to filter out what routes it advertises out of an interface (G0/1), Would I be able to filter based on the classful boundary of all the subnets or will I need to define the classless subnets. E.G The router has man...

Traffic shaping on Cisco 2960S

need some help here. Looking to move traffic shaping of my ASA5540 and onto my perimiter switches which are stacked Cisco 2960S catalysts. Doing this because ASA can only shape upto 150MB and my circuit just got upgraded to 450Mb my questions are: c...

Resolved! Cisco 1921 Configuration

I'm trying to configure a Cisco 1921 router to connect with my cable modem.  The router obtains an IP address from DHCP and I can ping resources on the internet while on the router.   The router hands out DHCP addresses to the clients but the clients...

smutnpj10 by • Level 1
  • 1518 Views
  • 2 replies
  • 0 Helpful votes

Unable to ping my Own LAN IP

Unable to ping my direclty connected client (LAN IP) from my router. Router Configuration as below Building configuration... Current configuration : 7288 bytes!version 12.3service timestamps debug datetime msecservice timestamps log datetime msecse...

View All
Unanswered Topics
View All
Review Cisco Networking for a $25 gift card