Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

BGP.

Hello,    I'm facing problem with ipv4 address. I have configured a list of address on bgp but few ip pool not showing mask, even though I have configure. Below are the output. network 192.232.131.0 mask 255.255.255.0network 192.245.196.0 mask 255...

Resolved! IP route not exist in routing table punted to CPU

Dear All,   Our equipment Cisco 7609-S today detected numbers of packets to ips not exist in routing table and punted to cpu which caused high cpu loading. Could you please advise if there any solution and how we can prevent such situation happen?As...

aweer1234 by • Level 1
  • 2558 Views
  • 8 replies
  • 0 Helpful votes

VLAN routing, am I missing something?

Hi, I recently asked a question here about vlan routing and what to do about moving a single switch (3550). Here is the link for the curious: https://supportforums.cisco.com/discussion/12922461/vlan-routing-help-requested I have since looked more in...

sharkerty by • Level 1
  • 2923 Views
  • 14 replies
  • 0 Helpful votes

Resolved! Internal Sub_Net !!!!!!!!!!

Hey Guys; I need some help here; two of my sub nets are not working; To make a long story short; I'm unable to ping my secondary or third network to my vlan switch which is causing my servers unable to communicate thru my internal network. See info b...

j_j624001 by • Level 1
  • 864 Views
  • 6 replies
  • 0 Helpful votes

BGP Configuration and Failover

Hello All, We have two links from two different ISPs on BGP. Both links are connected on different CE router at our end. Network diagram attached for reference. We are advertising two pools on this links , 192.168.10.0/24 from one ISP and 192.168.30...

keen4.net by • Level 1
  • 611 Views
  • 1 replies
  • 0 Helpful votes

Cisco CSR in AWS with GRE/IPsec Tunnel

I posted this as a reply to another discussion, but I thought it would be better separate. We have a Cisco CSR 1000 as an AWS EC2 instance with two interfaces.  We have a tunnel setup with a customer.  We have an AWS server that can communicate with...

OSPF Full to Down

I´m getting the following message: Mar  1 12:16:36.739: %OSPF-5-ADJCHG: Process 50, Nbr 172.19.94.141 on GigabitEthernet1/1 from FULL to DOWN, Neighbor Down: Dead timer expiredMar  1 12:16:41.795: %OSPF-5-ADJCHG: Process 50, Nbr 172.19.94.141 on Gig...

Resolved! Switching from DS3 to Switched Ethernet Circuit

Hi Everyone,  I am trying to switch from a DS3 circuit to a switched ethernet circuit. We have 2 campuses both with a 3845 router which has a DS3 modules on it. We recently purchased a switched ethernet circuit provided by AT&T. I thought I could ju...

Resolved! SPAN on 3945

Hi, I am having trouble configuring SPAN on a 3945 with 15.0(1r)M13. gi0/0/0 is a HWIC I added because I was seeing the same behavior on the onboard ports. Is there a specific issue with this or am I mussing something? rt(config)#monitor session 1 so...

Configuration upload to remote router

Is there a way to copy lines of configuration commands to a remote router before applying them. I have several new lines of config to add to various routers but will cut off my connection before being able to upload all the lines.

Resolved! VLANs

Hi, I am new using Cisco Meraki devices and, I would like to know whether is possible to configure a port on the switch that allow different VLANs, (ok that is easy one just configuring the port as trunk) but what I want is: that port is going to be ...

Load more