I try to link Huawei S1700-28FR-2T2P-AC to S3700-28TP-EI-DC with eSFP-GE-SX-MM850 from the two sides but the module led was off from the S1700 side.Is any wrong with the Huawei S3700 switch, which part should I check?
I try to link Huawei S1700-28FR-2T2P-AC to S3700-28TP-EI-DC with eSFP-GE-SX-MM850 from the two sides but the module led was off from the S1700 side.Is any wrong with the Huawei S3700 switch, which part should I check?
On which IOS version is BGP auto summary is default?
Hi, I'm trying to get an ip community-list to accept a community with a 4-byte ASN. I'm running image c7600s72033-adventerprisek9-mz.152-4.S4a.bin on a cisco 7603 router. When i try to input ip community-list standard NAMEDLIST permit 0:XXXXXX with t...
Why can't an SVI be used for advanced L3 forwarding features, but a "routed" (EHWIC) wan port can?I'm asking this, because since almost all ISR G2 (Cisco 8xx, 19xx, 29xx, 39xx) routers are using a generalized CPU platform, so the CPU is involved in ...
Dear TeamCan any one help me :Here are the details of switchsh versionCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (...
Hello Everyone, We have 3 locations which server as our data centers, each location has a pair of 6506E in a VSS configuration. In one of the data centers, we are having to relocate the pair of switches to a different location. The question i have is...
Good afternoon, I'll provide a brief description of the enviroment, currently we have 4 Cisco SG500-52 switches, there are no vlans setup, just native vlan 1. 2 switches are for data and 2 are for voice. When we first setup the switches we ran out of...
In a Cisco MPLS network with QoS and multicast VPN is experiencing huge RTP packet loss. Explain your logical approach in troubleshooting this problem.
HI,At work place I had CISCO 1841 routers with 128 MB Memory and 30 MB flash. Can I use these routers for IPv6 by updating hardware and making existed IOS version to 15 without data loss problems Can you please update on thisThanks Regards,Vali
I am trying to find the command that will allow me to delay a remote device from writing a series of commands to configure the link I am communicating over. Once I write the first 2 commands it will dump the link I am remoting into it with.. Can some...
Hi All,I configured route summarization eigrp. When pinging the R2-destination from R1-source(two hops away) it appears I have some sort of routing loop because I drop packets. I have attached my topology. R1, R3, R2. R3 is in the middle with two i...
Hi all, I'm doing a bit of an experiment at the moment tracking an ICMP reply and the route it takes through our lab network however I've come to a bit of a dead end. If I do a "debug packet ip detail" on our destination router (Where we are trying ...
Hello. First time, turned on 3650 for first time and all went well.Second time I started to see stange messages about poe being enabled and disabled.Third time a got a loop boot; after 5 reboots it goes to rommon. I tried to boot from usb with a bin ...
Hello, I have downloaded this IOS filec2951-universalk9-mz.SPA.152-4.M7.bin.Now, please let me know the steps to upgrade the firmware on ISR C2951 router. Thanks,
We have a CISCO 800 series connected to 2 WAN channels, and 2 VLANs. The idea is to have VLAN1 always use WAN1 channel, and VLAN2 use WAN2 channel, but in case of connectivity failure switch to a working channel. Important to say that both WANs use D...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-06-2025 06:09 PM | ||
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 3 | |
| 1 |