Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

Two debugs : one per vty

Can somebody tell me how to do this? Example, debug ip ospf interface brief output on vty1 and debug ip ospf events on vty2? or any other way to uniquely identify out put of different debug commands?

pgamage by • Level 1
  • 376 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Problems to reach some websites

Hi,I'm asking for your help about a problem I have been struggling with for about a month.Background information:- 3 client computers (2 on Windows Seven, 1 on XP), - 1 Windows 2012 server (AD service active)- ASA 5505 router for the WAN connection (...

Resolved! ACL Applied in Inbound direction and another ACL exist for in outbound direction - will return traffic allow

interface gix/yip address A.B.C.D 255.255.255.192ip access-group ACL-Inbound inip access-group ACL-Outbound outexitIn ACL-Inbound I have allowed SMTP traffic 6 source address to 4 destination server. One sample output among 24 acl is given below.perm...

rvs4000 v2 upgrade problem

tried to do a firmware update to router and it failed.  red then green led's blink alternate. Can not use the utility .  states broadcast error, browse device error I have tried a hard reset of more than 10sec.  does not work what to do next ?I was a...

drahcir77 by • Level 1
  • 157 Views
  • 0 replies
  • 0 Helpful votes

Resolved! Replacing the DMVPN hub router

We are replacing our current 2921 router, Version 15.2(4)M2, with a 3925 Version 15.2(4)M6. It is the DMVPN hub router for 6 spoke routers. We cut and pasted the configuration from the old router to the new. We confirmed internet connectivity from cl...

Resolved! Connecting CISCO 1921/K9 to Satellite Modem

Trying to connect 1921 to Excede satellite modem; neither has a serial port so I am trying to use the RJ45 ports.  How do I configure Gigabitethernet 0/0 to pass the traffic on to the modem? I  have GE 0/0 set to IP 192.168.100.10, with ip NAT outsid...

HTTPS fragmentation issue over IPSEC VPN

Hello,I've got a problem that hopefully you can help with: Remote Office.PC - MTU Default 1500Switch - MTU Default 1500Firewall - MTU Default 1500Cisco WAN Router:inside interface - MTU Default 1500outside interface - MTU 1600>>>Note: Outside interfa...

multicast ip-pim-sparse mode

 Hi, my consideration are correct  for the multicast protocol ?As for the command "ip pim rp-address 173.17.2.1 VALID_GROUP" which is on the site of Padriciano I did a search and, practically, it automatically creates a tunnel interface.  This thing,...

CISCO 2811 Router and MPLS

I have a 2811 router connected to a MPLS (MetroNet) fibre switch via a CISCO 2950 switch. The local and remote routers have tunnel interfaces to connect over the link. The circuit works most of the time but occasionally drops instantaneously and come...

Cisco BGP Peering Between 2 ISP

Hi Cisco People, Just have a question with BGP peering in Cisco's. I have two ISP's which I am peering against for an active and standby configuration. I would like to know if there is a way to configure some sort of 'dead-peer detection' on the rout...

View All
Review Cisco Networking for a $25 gift card