Hi guys,is it possible to downgrade a rommon image on a ESP20?We are trying to downgrade from 15.3(3r)S to 15.0(1r)S and it seems not to be possible, ASR1k-01#sh platformChassis type: ASR1006Slot Type State Insert...
Hi guys,is it possible to downgrade a rommon image on a ESP20?We are trying to downgrade from 15.3(3r)S to 15.0(1r)S and it seems not to be possible, ASR1k-01#sh platformChassis type: ASR1006Slot Type State Insert...
Dear AllThe service-policy ... could be put under interface and control-plane. What is the difference between the two sites when service-policy is used ? Thank you
Hi, I'm a Korean engineer. Today, I have a trouble about backbone supervisor module WS-SUP720-3B. I tested module WS-X6148A-GE-TX with SUP720-3B. But, in the CLI, this sentense came out ... "not support slot 2, 3."(slot 2,3 = WS-X6148A-GE-TX)So I r...
Hi Everyone,I've been fighting an issue with a 2821 router for some time now. I'm trying to pull the top talkers from an interface, however the cache is empty. I verified the configuration with a known working 2821 and the output for the interfaces a...
Hi Frens,I have a WS6509-E which is running on below IOS had a software reset yesterday, however I am not able to identify the exact reason for this to happen. Could you kindly let me know if this is relate to any bug or is it something ussual for t...
Help urgentsomeone gives me real configure and works well using PPTP VPN and Cisco Easy VPN on a Cisco RouterThx
Hi all,I have an old switch C3524 running image "C3500XL-c3h2s-mz-120.5.2-xu". I had successfully created vlan 120 but when I config "interface vlan 120" as follows:swicth # conf tswitch(config-subif)#interface vlan 120switch(config-subif)#ip address...
Hopefully somebody could help me with a router setup.The setup is as followsISP -> Cisco router -> Firewall (Sonicwall)All I want the cisco to do is to pass the traffic to the firewallI presume i'll have to give the sonicwall interface an IP address ...
Just attempting to set a simple configuration on this router. I want a static on the WAN FE4 and a dhcp server on the VLAN for the switch ports 0-3.I can get the DHCP working and ping the cisco from my device but I can not go any further. Originally ...
I have a difficult problem...Please forgive my ignorance.I have a consumer-grade router called a "Fritz!Box 7390" on the edge of our network (in Germany -- very capable, very popular little box).Following are the telephony characteristics:ISDN BRI is...
Hi, What is the concept behind ECMP (equal cost multi path) ? Is it different for EIGRP , OSPF , ISIS etc ? thanks
Hi,I’ve a generic multicast question.Let’s say I’ve two different source sending different multicast traffic over the same multicast group, how can I solve the problem for a customer receiver ?S1=1.1.1.1 G1=224.1.1.1S2=2.2.2.2 G2=224.1.1.1C...
I want the below routers to work as ACTIVE & STANDBY ,The 2 routers share the same configuration ( automaticaly ) When active is defected shutdown the standby works as active Existing router :- cisco2811-v + VWIC3-1MFT-T1/E1 New added router :...
I have two routers that has a static route configured for the LAN side which re-distributes via BGP to the WAN. One of the routers does not have anything connected to LAN subnet/ interface. Other one is live. Will this create a routing conflict in th...
We have a MPLS WAN connecting our offices from our Service Provider. Our Head Office has a larger 50Mbps pipe and a remote office has 2 separate 2Mbps links (lets call them link1 and link2). Right now all traffic only goes over Link1 at the remote of...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM |
| User | Count |
|---|---|
| 9 | |
| 6 | |
| 4 | |
| 4 | |
| 4 |