Routing

Resolved! cisco 887 portforwading

help i want to port forward using my static ip 10.10.10.2 3389 and 10.10.10.2 1167, I am newbie at cisco please show me what command i will use,help guys :(no service padservice timestamps debug datetime msecservice timestamps log datetimeservice pas...

Resolved! Interconnecting 2 sites

I want to interconnect 2 sites through dark fiber using L3 connectivity. Currently the 2 sites are connected through ISP L3 MPLS.The 2 sites have Core switches redistributing static routes into OSPF routing protocol and then get redistributed into th...

Named EIGRP for IPv6

Hi, I'm trying to do some lab testing and tested named EIGRP. I was able to understand the EIGRPv6 configuration where you configure the EIGRP statement under the interface and by issuing "no shutdown" under the EIGRP process created. So basically al...

rj45 to rj45 console cable

Hi i want to connect a Macbook pro using a rj45 to rj45 console cable to set up a switch but i don't know what to do and no information about it online only about usb. Can anyone help? Thanks

Cisco 887VA VDSL with high CPU utilisation impacting performance

I have a Cisco 887VA router that has a working VDSL configuration. It syncs with an attainable rate of 48932 kbits/s and 13432 kbits/s. Speed tests max out around 38Mbits and I can get download speeds of 4.5MB/s but the CPU utilisation hits the roof....

connecting a Cisco router to a cable modem

I am having a problem I hope someone can help me with. I have a Cisco 2801 router with a 2950 switch. I have the switch configured with 3 VLANs and a trunk established in a router on a stick configuration. The VLANs function perfectly, but I do not h...

Resolved! Problems to track default routes on IP SLA

In my router, there is a default route with the administrative distance 1 with track 1 This route is used for an internet link. 0.0.0.0 0.0.0.0 172.19.4.10 I also have 2 dialers to redundancy with the administrative distance 20 and 30 respectively....

Cisco 887 router with URL Filtering (Websense) issue

Hi there,Thanks in advance for any help on this. I have a cisco 887 router that connects to a websense server for url filtering. The configuration used looks like this: ip inspect name fw_url http urlfilterip urlfilter allow-mode onip urlfilter ser...

Resolved! Ip address dhcp

Hi, I have taken an internet account with an isp. The account is a dhcp account and I have to give username and password from webpage while connecting it through computer. Is it possible to connect the same link with cisco 1841 router. I got the ip ...

Remove Flash Partitionin 2651XM

We have router 2650XM with the partions which i need remove.Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-ADVSECURITYK9-M), Version 12.3(5c), RELEASE SOFTWARE (fc2)Copyright (c) 1986-2004 by cisco Systems, Inc.Compiled W...

Resolved! Cannot configure SGBP through a stack of routers

Dear Cisco community,I can't configure SGBP (Stack Group Bidding Protocol) with 2 routers. the topology is simple:ROUTER1------int F0/0------------int F0/0-----ROUTER2ROUTER1 configuration:aaa new-modelusername mystack password ciscohostname ROUTER1...

Resolved! Routing via Core

Guys, I need a little advice and expertise, I am new to this.I have a point to point 1Gb link, from my location to another location, every now and then it goes down, at that remote location is dead in the water.So we have added a VPN in the picture, ...

New to BGP

Hi Guys,I am wondering what is the best - most effiecient way to have inbound traffic to a specific network in our NOC advertised out to peers. We have two gateways to IXPs and we are peered with about 5 others in each IXP. How shall i configure BGP ...

SSDP (Multicast) over VPN (PPTP)

Hello everybody,I set up a Cisco RV180 VPN Router with VPN (PPTP) enabled. Everything works fine so far. When i'm connected to the VPN from a remote Network with an iPhone, iPad or Notebook i'm able to ping all devices and to reach the setup pages wi...

Resolved! Auto Provisioning Cisco Router

Hi' i'm wondering if there any feature for auto-provisiong of the interfaces, connected to ISP.For example, in Huawei Routers, i can configure Fast-Provisioning, this featureenable an auto configuration for the ip address point-to-point when the inte...