Hello community, PE CE --------------|.....| ---------------------------------------|.....| MPLS multilink PPP via E1 I am looking for a solution for the fo...
Hello community, PE CE --------------|.....| ---------------------------------------|.....| MPLS multilink PPP via E1 I am looking for a solution for the fo...
Hello @ all, i have a Cisco 4500 with Sup 7.I need Multicast Routing between VLan 2 and VLan 3 and a seperated VLan Routing beween VLan 4, VLan 5, VLan 6 .. What´s the Config that i need for this ? .. can anyone help ? Thanks a lot
Hi Guys, Please provide the resolution for this issue. Please refer the above diagram, IBGP & EBGP configured, routes are propagated from Ibgp to Ebgp, but Router5 unable to reach EBGP routes.Router 5 able to see the Router 6 routes with next hop is ...
Hi all, I would like to know how can I limit the bandwidth to specific web pages, (Facebook, YouTube). With my Cisco router 2800. Thanks.
Hello all,Probably this question has been asked thousands of times before, but, after going through the answers carefully, I have to admit that I could not find a satisfactory explanation for the OSPF point-to-multipoint non-broadcast option.What exa...
Hi, We have a Cisco3925 router with IPSEC license installed in it. We are planning to upgrade the MPLS link from 40MB to 60MB.Just wanted to understand if the Cisco3925 router support this BW? and will there be any limitations on IPSEC license?Wh...
hi guys,I would appreciate some assistance here. We have a primary head office & a DR site. Routers at both sites connect to our carrier for an IP VPN service using BGP. BGP configs on each router advertise a default route 0.0.0.0. #sh ip bgp neigh...
Hi Guys,Can someone explain to me why it is recommended to leak loopback addresses to ISIS in MPLS VPN environment ?In Cisco website it says this "In MPLS VPN environments, reachability information for the loopback addresses of every Provider Edge (P...
Good morning,Does anyone have sample configuration for STP, for what they normally configure on their access, distro, and core switch? I would like to see how other organizations have STP set up for each one of their switches, depending on the functi...
Hi Friends,We are experiencing issue in Cisco 6004 while creating VPC. We are unable to configure VPC because upon enabling the feature it is showing error.Request if anybody can help us here.TEST(config)# feature vpcError: while enabling/disabling...
As i am a newbie, i read the BBA configuration guide, and try some commands in this guide.When i enter the "interface atm 0" command in global configure mode, it said "Invalid input detacted at '^' marker.Hm, the router is 1941 without adsl wic, is t...
Hello, I hope someone here can answer my questions. I have asked some of the CCIE's on my team and opened a TAC case, but neither option provided solid answers. The short version of my question is this: what does "5 minute rate XX bps" mean in the co...
hello.We are going to buy a 1905 router but we need to fix a performance table comparative between: 1905, 1921 and 1941.We have reviewed cisco web and other link at internet but i can not find the performance in PPS and/or Mbps for...
I have a scenario where we have 2 MPLS providers. Each of our sites runs EIGRP which is redistributed into BGP for each MPLS provider and vice versa.Currently the loop protection mechanism is to use prefix-lists at each site which dictate what should...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM | ||
04-22-2025 12:20 PM |
User | Count |
---|---|
9 | |
7 | |
4 | |
4 | |
3 |