Buy or Renew
Buy or Renew
COMING SOON: Umbrella and Secure Access release notes are coming to Cisco Community. The community will be in read-only August 16 – 19. Learn more.

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Start a conversation

Resolved! cisco nat, dynamic ip from isp

Hi!I think I understand the cisco NAT-PAT thing, but I try to manage this at my office with a 1841 router, and I don't know how to solve, that my ISP uses dynamic IP-s, and every 24 hours the public IP address is changing.Must I change the router con...

LOTS of Reading, Out of Ideas

Well, I did a lot of reading and a lot of searching (excruciating details below) and am still not able to get to my server from outside on the web.ssh dev.optuserv.com  (the domain I've set up) results in:ssh_exchange_identification: Connection close...

gmark by • Level 1
  • 647 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Overlapping 192.16.x.x subnets

HelloI acquired a comany comprising of 5 sites. I am phasing these onto my AVPN network which currently consists of 12 sites.The phasing aspect is being done by denying their subnets from my current routers and vice-verse.The new sites have re-ip add...

Cannot Access The Servers (Nat not working)

We are not able to connect to our Servers using Microsoft Remote Desktop from wan side. The Configuration of the router is:service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname Branch!boot-star...

Resolved! 2901 router

I have 2901 cisco router.Running one gateway on it, is it possible to add more vlans or use psyical interfaces to run multiple gateways? Its important that they are seperat, that the routes are for each interface.Regards jSent from Cisco Technical Su...

Clocking Help

                   Looking for some assistance in setting up clocking correctly for the following setup:(4) T1's - serial 0/0/0, 0/0/1  --  0/2/0, 0/2/1(1) PRI 0/1/1Currently its configured like this which can't be correct because there is no working...

EIGRP external route redistribution

Hey everyone, my mind just pulled a blank and I need some help.Say I have 3 routers; R1, R2 and R3R3 has a static route to 135.xxx.xxx.xxx pointing towards a firewall. R3 is re-distributing static routes via EIGRP to R2R2's routing table has entry th...

Ricky S by • Level 3
  • 2428 Views
  • 3 replies
  • 0 Helpful votes

Multiple ISP Failover

Hey All,I am stuck in problem when doing a senerio and need your help. I create one topology in this, My Router CE_router is customer router, which is connected to BSNL_ISP_1, the BSNL_ISP_1 node going in MPLS cloud. In my senerio i have create datac...

HWIC-CABLE-D-2 ... DOCSIS 3 ?

We have an ISR 2801 with a HWIC-CABLE-D-2. Within 6 months we expect a DOCSIS 3 rollout to our area.Is there any hope for a HWIC-CABLE-D-3 or another DOCSIS 3 compatible HWIC?It would be even better if it was compatible with the ISR 2801.I can't find...

Apaxmai13 by • Level 1
  • 18638 Views
  • 14 replies
  • 0 Helpful votes

Resolved! Clock in Logs

Hello Friends - I am seeking your help in understanding why the timestamp shown in Logs differ from Router Clock set thru NTP. Here is my observationNote: both the routers are SYNC with NTP server at Strarum 3Router-1 Configurationservice timestamps ...

Resolved! Cisco 3560G is not marking the packets

I have configured QoS, for marking some packets as CS2 in a Cisco 3560G with a 12.2(55)SE. But I check in a router that is the next-hop and dont see the packets marked.! This is the internal interface:interface Vlan1888 description usuarios-gbs-claro...

how to monitor url?

Hi there,              How to monitor users url in a campus environment....? (about 200 users)              Is there any cisco devices are available to do this job...?Thanks in advance....!!!!

Resolved! Dual NAT on multiple ip addresses on cisco 800

Hi,i'm trying to figure out the configuration to obtain a dual nat routing.I have 1 + 8 public ip addresses: 1.1.1.1 255.255.255.2552.2.2.0 255.255.255.240Now i would have 2 private ip addresses on the router (192.168.0.1 and 192.168.0.2) so that cli...

maudam000 by • Level 1
  • 3286 Views
  • 6 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card