Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Resolved! L2TP over ADSL

Please help!!I have 2 887va routers which are both connected to an ADSL line and each other by VPN.I am trying to set them up to pass layer 2 traffic. I have followed all the help I can find but they still fail to pass layer 2 traffic.Below is the co...

dannymcca by Beginner
  • 3026 Views
  • 4 replies
  • 0 Helpful votes

I am trying to setup the following.I want to have all Internet traffic to go through ISP2All Corperate traffic to go through ISP1If ISP1 fails I want the Corporate traffic to go through a VPN tunnel over ISP2If ISP1 comes back up and after a couple h...

burleyman by Collaborator
  • 559 Views
  • 1 replies
  • 0 Helpful votes

Hi we need to translate x25 packets to a tcp stream. The translation works fine but our electronic payment terminal application has problem with the received data stream from the router. Our router sends in front of the application data a 4 byte QBit...

Hello frineds'I have one cisco acs server verson 3.0 and i want to enable mac binding in my all cisco switches in my network through radius.Any one have idea to implement to my network.if you have any document ,pleaease share with meplease tell me th...

Hi all,I'm looking at a production router with a VWIC2-1MFT-T1/E1 module and neither side of the serial p2p connection has any clock rate configurations. Now I know with the VWIC2-1MFT-T1/E1 that everything is configured under the controller interfac...

Obtained a 3G ISR C819HGW+7-N-K9 for use as a backup device for Warehouses in Australia.I have followed (and tried) most of the discussions I can find in the manuals and online for getting the 3G operational - without success.The SIM has been tested ...

I recently purchased a UC520W for use at home to replace an 877W, would  like it to do all the front-end stuff, NAT, firewall, PPPoE, voice. Have  installed a 1801 in front of it to bridge ADSL to Ethernet (almost),  but having some issues. 1801 conf...

azaghul33 by Beginner
  • 1563 Views
  • 3 replies
  • 0 Helpful votes

Resolved! cisco 2821 eigrp

Hello, i have a cisco 2821 router with c2800nm-advipservicesk9-mz.124-15.T9.bin. I want to connect it to a cisco 886va and run eigrp on both routers.I want to ask if using eigrp requires any kind of license or it is supported by default..Thank you..

Hi, we have a model CISCO857W-G-E-K9  with IOS version 12.4(15)T17We're trying to install Cisco Configuration Professional Express 2.7 and in particular the package cisco-config-pro-exp-admin-k9-2_7-en.zip following the install guide we found here T...

Ive been trying to get a lab scenario to work that i came up with on my own. Not expecting it to be so troublesome of course. I have the topology pictured below:The only issue is that R2 cant ping R3 and vice-versa. All the routes show up in the BGP ...

I have something I really don’t understand about l2vpn in comparison to l3vpn connections.With l3vpn we have 2 mpls label the top label for communicating between the PE and the PE (most likely loopback ip’s of these routers) and we have the mpls vpn ...

Thanks in advance for your supportI have this question below:                 I have 2 routers C1 and C2 connected to NMS in Area 1, the NMS is configured with ISIS Level-1These 2 routers are connected to 2 other routers A15 and A17 with Serial links...

simonixus by Beginner
  • 515 Views
  • 6 replies
  • 0 Helpful votes