Hi guys How to summarize these routes on ASBR router ? : These routes belong to EIGRP I already redistributed to OPSF as well. 140.15.0.0 255.255.0.0 140.16.0.0 255.255.0.0 140.16.0.0 255.255.0.0 140.17.0.0 255.255.0.0 When i summarized on ASBR #Rout...
Greetings,This is a PoC and I'm a bit new to this. That being said, I tried kicking this one around a bit just to see if i could figure it out. It seems I need a second (third, or fourth?) set of eyes please.My goal is to set up a dual hub dmvpn scen...
Hello can someone help me I have a problem with Cisco router c7200 I'm trying to make a backup link between two routers but for some reason when I disable the main interface the backup interface doesn't turn on it says disabled, here is my config:R1#...
Hi AllI am looking at upgrading some internet connections to 10G, our current 4451 routers will not give us the throughput so we need to replace with a sufficient router or switch.Can anyone tell me what the best value router is to give us 10G throug...
Hello everyone, I am still a beginner and I'm trying to configure a network with predefined information in Cisco Packet Tracer, as seen below. However, I've never worked with this kind of configuration, my guess is that this is a trunk port on a rout...
Hi all,I'm configuring my 1st Cisco ISR1113 router, which we are using as replacement for the 897 small office routers. I'm trying to use the USB flash with no joy. The data sheet for the ISR1000 routers shows flash memory support Type A USB 3.0, and...
Hello,Here are the firmware versions on the router with IOS asr1000rp2-adventerprisek9.03.16.10.S.155-3.S10-ext.bin:Chassis type: ASR1006 Slot Type State Insert time (ago) --------- ------------------- -----------...
We are running several remote sites connecting back to a central site using EIGRP as the routing protocol over AT&T's ASE on demand switched ethernet service. It's been mostly fine, but occasionally for 25 or 30 minutes we get a lot of flapping that ...
Hi All,We have recently configured a TSG 1100 but we have not been lucky in getting ssh/telnet access on any Console port connected to it yet.For the config,we have configured a loopback address and a few ip hosts commands to map the loopback to host...
Hello, I have 3 routers that use BGP (Internal/External) + EIGRP for IGP. Here is the quick configuration of routers : -- R1 (fd12:3456:789a:1::1)ipv6 route ::/0 Null0router bgp 100address-family ipv6network ::/0R1#sh ipv6 route ::/0Routing entry for...
I am new to packet tracer and i have a project to complete.So basically there are 3 floors, each floor has a lab, class, faculty. the lab network is split into two using 2 switchs each connected to 20 devices. these 2 switches are connected to main s...
Hello,I'm working to configure a simple Dynamic NAT setup to allow inside hosts to reach the internet.When I apply the config, the host1 from inside the network gets 1 ping response, then it stops receiving responses. I'm pinging a host (host2) that ...
Hello,I have some uncertainties related to PIM Dense Mode operation:Imagine the following topology:The purple arrows indicate the paths of the multicast traffic stream, from the source (SRS).The assumption is that all the routers are configured with ...
I have network 10.0.0.0 10.64.0.0 10.128.0.0 10.192.0.0 with subnet of 255.192.0.0 in Area 93 which is summarized on R1Other networks 10.32.0.0 10.64.0.0 10.96.0.0 10.128.0.0 with subnet of 255.224.0.0 not summarized on R7Now! when i ping 10.63.255.2...
I'm sorry. 2 hours without finding solution.How to connect a 4221 router to my PC using USB port of the routeur and USB port of my PC.Using "Cisco_usbconsole_driver_3_1.zip" don't create COM port.I'm working in network since 30 years. CCNA certificat...
| User | Count |
|---|---|
| 12 | |
| 12 | |
| 7 | |
| 6 | |
| 5 |
