Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I multi homed to dual ISPs using a single 6509e. Currently, I am only receiving a default from wash ISP and marking one with a higher local pref. most of my traffic flow is inbound, so this config meets my need. The issue I have: if either ISP has h...
Hi all,All what I'm describing is made with a Cisco PIX Security Appliance Software Version 8.0(4)28. I'm trying to give access to an internally NATed system for VPN RA users.Basically, they open an IPSec session and are hosted in a first subnet (172...
I'm configuting remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my lo...
Hey All, I'm learning about static routes now and just cant seem to "see" it when it comes to routing through multiple hops. I get it when routing network to network (1 to 2 hops), but if there is a 3rd router to travel through in there, I can never...
Hi Experts,I have Scenario as attached, N below is the description1) Eigrp 100 in on WAN cloud.2) Eigrp 10 is on internal Network at Head office.3) I am Redistributing Eigrp 100 in Eigrp 10 at R1 & R24) Redistribution metric on R1 is kept low than R2...
the last is computer in ipv4 can ping the ipv6 computer...i want trying to use RIP route...can i get the command and some explanation??
I have recently connected a 10 Gig connection from the local telco between two sites on 6509's. These two sites also have a 1 Gig links between them. When I connected the 10 Gig link I expected the 10 gig link to be the preferred route, but after l...
We have a ME6524 running as a MPLS P router. We want to mirror a port to capture a specific traffic stream (to a probe). As the port is an MPLS LDP port will this work, will both the VACL and SPAN work with MPLS tagged packets, or does the mirror and...
I have seen on the core switch I am working on currently there is not the 'ip routing' statement. HOSTNAME#show verCisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(54)SG1, RELEASE SOFTWAR...
Dear Sirs!We have next router:spb-bg3#sh inventoryNAME: "CISCO7604", DESCR: "Cisco Systems Cisco 7600 4-slot Chassis System"PID: CISCO7604 , VID: V01, SN: FOX1523H7E8NAME: "CLK-7600 1", DESCR: "OSR-7600 Clock FRU 1"PID: CLK-7600 , VID...
Hello. Please help me with SmartEdge 100. I have 1 "white" global ip adress.How config NAPT overload for give internet access to that network 192.168.1.0/24.In cisco: ip nat inside source list ACSLIST interface GLOBALINT overloadHOW do this method in...
Greetings,I have a question regarding ip nat inside command which may explain an issue i am facing with a client..Suppose we have:ip nat inside source list 101 interface Dialer1 overloadip nat inside source static 10.0.0.250 87.202.212.131 route-map ...
Hi,I'm doing a VTP pruning experiment using the following network structure in PT, unfortunately it's not available. And I think 'switchport trunk allowed' command is not an alternative since it will yield different results. Scenario: -vtp prun...
What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582-2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 Here is some output:...
Hi,We need to implement QOS in our LAN environment - access, distribution and Core level , How can we setup QOS for VoIP and video traffic more effectively, give me more realistic data ( I meant realtime configured detials) or good document which mo...
