Like to have the option to increase Packet Tracer capabilities to boot custom ISO to add to the lab. would help greatly to illustrate the metwork simulation on real live
Forum Posts
Hi, is there a way to find out why a NBMA neighbor went down. In the case below You can see that the neighbor is only up for 1 day and 4 hours. However am unable to find out why. I checked OSPF and neighbor status and it never went down. I did see a ...
Hello. (obfuscated)ASA1100#sh route staticGateway of last resort is 63.229.172.2 to network 0.0.0.0S 172.16.0.0 255.255.0.0 [1/0] via 172.16.99.1, insideS 0.0.0.0 0.0.0.0 [255/0] via 172.16.99.1, inside tunneled---# sh route 0.0.0.0 0.0.0.0Routing en...
GIVEN: config... Conf tip prefix-list BLOCK-ANYCONNECT-SLASH-32-SUBNETS seq 10 permit 172.16.77.0/24 ge 32ip prefix-list PERMIT-ANYCONNECT-SLASH-24-SUBNET seq 10 permit 172.16.77.0/24--route-map RM-BLOCK-ANYCONNECT-SLASH-32-ROUTES deny 10match ip pre...
show crypto isakmp sa Empty result Please help me on this
Recently, I am migrating from 2900 to 8200. When trying to copy rate-limit configuration, the command is rejected.on 2900:interface GigabitEthernet0/2description AIRTEL_MPLS_20Mbip address x.x.x.xip flow ingressip flow egressrate-limit input access-g...
Hi All, I am very new to the networking world I am wondering if I am making an easy mistake somewhere. I have a network consisting of a cisco 2921 router and 4 copper cisco switches. Into the router, I have a link to an ISP who have given me a publi...
Resolved! Need Help in Static OSPF Redistribute
Hi , Im very newbie in networking. i have question about OSPF routing with Static. i have this configuration below, why i cant ping R5 and R1 network from R4, even though i can see their network in my ip route, i can ping it also from R3. is there a ...
Hi everyone,At present, our company is using a router cisco1941, the original RJ45 console port has been damaged, recently I need to connect it to modify the Settings, I can not access the device using the USB mini port. My laptop is running the vers...
Hello everyone,I recently replaced some EOL equipment because the vendor had set the WAN port0/0/0 in the router to be used as LAN.The LAN port 0/1/0 is used as WAN and it is emphasised that this is the standard of the vendor.I would like to know wha...
Hi, can anyone please advise whether can config graceful restart of bgp for individual neighbor? Global config level, we don't want to enable graceful restart. Thanks in advance!
Hi guys,I am new to MPLS TEI have read copious amount of materials and watched a few videos.But the main points of how MPLS TE works seem to get lost in a lot of jargon. Please could someone in simple terms breakdown how MPLS TE actually does Traffic...
Resolved! One Network, Three Routers
Hi, I'm a bit new to Cisco, I'd like to know if this is possible This was presented by my teacher and he explain that in theory this is possible, but I know he likes to play tricks so I'm a bit skeptical on that. Is there any way this is possibl...
I see this on a cell site router , CSR shows Policy CSR-EGRESS Class class-default Classification statistics (packets/bytes) (rate - kbps) Matched : 9536213184/13231795438297 946742 Transmitted ...
Hi All, Pleas refer the attached diagram. I have a requirement to create redundancy between a 6509 and an ASR-1k (which acts as a server) by having 2 physical links between them. Also I will have to use an IP from the existing vlan in 6509 (VLAN-10...
