Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

AS Path access lists

Hi allCan anyone tell me how AS path access lists work, if I had the below on my router, what would it do, do they go in sequence etc ?ip as-path access-list 10 permit _2005_ip as-path access-list 10 permit _2006_ip as-path access-list 10 permit _200...

Resolved! BGP default route route-map

Please adviseI have BGP peer with upstaream ISPI need recieve default route onlyI want to do this via route-map with prefix-list (not just perfix-list)How can I do this?Now I do next (but it doesn't work)router bgp 5xxxx bgp log-neighbor-changes bgp ...

etherchannel is down at catalyst 6500

Hi dears. I have 2x6500s series catalyst core switch. i configurated vss. all them are working normal. but i have one problem. some of my servers link is down sometimes. I configurated server links as etherchannel.at etherchannel  not both of links d...

Resolved! 2610XM - Issue with SegV exception

Hi all,I have one issue with 2610XM which reload by itself. I checked the crashinfo file found the router was reloaded on 12:03. I'm wondering is it software bug issue or hardware problem. Thanks in advance for sharing any ideas . System returned to ...

Rojer-bkk by • Level 1
  • 1116 Views
  • 3 replies
  • 0 Helpful votes

OSPF E1 path selection

Ospf  E1 route preference  via 2 mpls links.We have a MPLs connection via level 3 from India to US running OSPF,  recently we got second MPLS link from AT&T now since AT&T is running BGP over their cloud we asked them to run ospf on both the sides fa...

Dual WAN with NAT/PBR

I'm hoping someone can shed some light on getting this to workWe've got a Cisco 877W (Test) & 1841(prod) with two PPPOE/Dialer interfaces to two different ISP (NAT overloaded). We've tried the examples on both platforms and with 12.4 and 15.1. We hav...

robardill by • Level 1
  • 4429 Views
  • 8 replies
  • 0 Helpful votes

Ripv1routing table

Hi i have two routers R1 and R2. Ripv1 is the routing protocol. What will be in my R2 routing table.R1 configurationFA0/0 - 131.108.5.0/24FA0/1 - 131.108.7.0/30S0/0  -  131.108.6.0/30R2 configurationFA0/0 - 131.108.2.0/30S0/0  - 131.108.6.0/30

Resolved! Bandwidth Management - Best Way

I need to rephrase this question. Let's say we have 100Mbps WAN link to the ISP, we have CustomerAand then the rest of our Customers. We want CustomerA to have lower priority than everyone else overthe WAN links. What is the best way to configure thi...

Resolved! IP SLA problems

have this configip sla 1icmp-echo 62.6.200.5timeout 1000threshold 2frequency 3ip sla schedule 1 life forever start-time nowtrack 100 rtr 1 reachabilityip route 0.0.0.0 0.0.0.0 "our-next-hop" track 100ip route 0.0.0.0 0.0.0.0 Dialer0 254ip nat inside ...

rasoftware by • Level 1
  • 7332 Views
  • 30 replies
  • 0 Helpful votes

7600 XL IPv4 vs IPv6 prefix limit

How does everyone normally split 7600 RSP/SUP720-XL maximum routes between IPv4 and IPv6 these days?I usually do 700k and 160k.show mls cef maximum-routes FIB TCAM maximum routes :=======================Current :-------- IPv4                - 700k M...

Resolved! QOS on cisco for limiting Youtube traffic

Hi Folks,We have a websense proxy. Till date youtube is blocked on the proxy. Now there is a requirement to allow youtube. Here is the question.The websense would send the traffic to the internet firewall which will send the traffic to the internet r...

Access list help on router

Hello,From the remote VPN side (ASA 10.100.1.66) into the VLAN 10 network (10.104.10.x) on this routers LAN works inbound on ports in the 123 access list, however I need to allow VLAN 10 on this router to go outbound to the the remote ASA VPN (10.100...

Load more
Unanswered Topics
View All