Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! 1921 Router/Link Bonding

Hello!Is it possible to bond two T1 lines for increased throughput and for possible failover situations? I currently have the second T1 as just a fail over.Thanks!Jason

Help with accesslists on Double Wan

HelloI'm having trouble because I can only have one internet connection at a time for it to work. If I connect the 2 wan to the router then the 2 of them doesn't work. I'm pretty sure is a access list problem that I dont know about. Please help me to...

edgsoccer by • Level 1
  • 3318 Views
  • 14 replies
  • 0 Helpful votes

Reset a 2600

I have a 2600 Router that has been donated to my use for some lab work.  The thing was locked down pretty well.  I have console access to it (obviously) but there is a console PW assigned.  How can I reset the silly thing back to factory defaults inc...

Resolved! Sub-interface mac-address limit PPPOE session

Hi all,I have configured 2 sub-interface on same physical interface. And  the physical interface is connected to a Managed switch on trunk port. Both sub-interface is pppoe-client and dial to the DSL network. Both modem in bridge mode an connected to...

VWIC-MFT-T1/E1 and VWIC-MFT-G.703 Card

Hi TeamI have a doubt regarding when to use VWIC-T1/E1 cards and G.703 Cards.I have read the datasheet and found the only difference between two is that G.703 supports Unframed/Unstructured G.703 support.However i am still not clear in which scenario...

skallidu by • Level 1
  • 1349 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Choosing a 15.x IOS Type?

Can somone give me a brief overview of the differances between the new 15.x IOS Types.  I see that 15.x has 15S, 15M, 15M&T, as well as special deployment versions and 15.0, 15.1, and 15.2 versions.  I really miss the old labeling scheme of Mainline ...

NPT_2 by • Level 2
  • 1573 Views
  • 2 replies
  • 0 Helpful votes

VPN NAT Issues

I have a slight problem here.  Our setup is as follows Internet -> Main Site Router -> Serial to Remote Site Router -> Voice/Data Network on said Remote Site.  On their voice network, they have cameras connected in on the remote site.  They want remo...

Resolved! bgp MED

bgp always compare-med.... is this one obsolete and no longer needed?I am doing my lab and it seems like route updates gets evaluated with metric attribute with or without  "bgp alwaysys compare-med" comman.iI thought in order for the router to compa...

ed by • Level 1
  • 2674 Views
  • 5 replies
  • 0 Helpful votes

Unable to enable Policy-Map on interface (QOS)

Hi ,Class and Policy maps are defined properly but when I am going to apply the policy-map on interface ,throwing an error as "'set' command is not supported in a 2nd level policymap".Class/Policy map configuration given below ....class-map match-any...

s.kanth by • Level 1
  • 2221 Views
  • 8 replies
  • 0 Helpful votes

Interface tracking(MPLS with BGP)

Dear all,I have a customer with 10 locations connected to their hub location via MPLS from two different ISP's ISP1- Primary MPLS ISP2-Secondary MPLSat 5 locations including hub they are running BGP with MPLS.(No problem here)in remaining 5 locations...

3G configuration Cisco 881G

Hi,quick question regarding a 3G access via a cisco 881Gi have a partner sim card (with the same number as the one in my mobile) iserted into the router.now i have the problem that my mobile is unreachable (line busy), is there a way to use both sims...

Load more
Unanswered Topics
View All