It's my understanding that a learned route via BGP by a PE and it's redistributed into OSPF, it will set the down bit. I'm trying to see this happen, but it's not. I have 2 CEs and 2 PEs in gns.CE1 --> PE1 <----> PE2 ----> CE2I have a route advertise...
I am trying to figure out how to configure a router to point towards a pair of off Lan MS dhcp servers in an 80/20 redundant/failover configuration.I typically use the ip helper-address x.x.x.x under the subinterface of the router for a single off La...
Hi everyone,I'm having some issues with a device that is renewing several routes every hour and I'm trying to understand what does this mean:BGP activity 95000/90000 prefixes, 155000/150000 paths, scan interval 60 secsI don't quite get what does thos...
Hi, I posted this on another forum but I'm still a bit confused.I'm a little confused over RIP vs RIPv2.I have read over and over but can't find a definitive answer in any of the books I'm reading.My question is, what routes does RIPv1 route too? I'v...
helo bro,assume i have a serial interface with default bw = 1.5 meganow if i used 3 subinterfaces , what is the bw of each subinterface >???? is it 1.5/3 or it is 1.5 mega for each one???thanks \
Hello,I was setting up the router with ADSL and in the course of setup I had the need to do a factory default. While doing that the system hing up on me and I had to shut down my PC. Now I am locked out of the router configs. The password I had creat...
I have a router thats one interface (GigabitEthernet0/3/0) flaps a lot. A The model of router is Cisco 2811 (revision 53.51). When I do the sh int command the output looks fine. #sh int GigabitEthernet0/2/0GigabitEthernet0/2/0 is up, line protocol ...
Hello,I would like to Upgrade license Cisco 1941-K9 from ipbase to security Anyone can help me ?Thanks
Hello there, i have a quick question about ip sla on a 2921 Router, i'm configuring it with the following parameters in order to test track. At the beggining traffic is up and it puts status on track with UP. If i take down the remote ip, SLA remains...
Here is the configs:class-map match-any Voicematch ip dscp ef policy-map INBOUNDclass Voice priority percent 40 set dscp efclass class-default fair-queue!policy-map OUTBOUNDclass Voice priority 1000class class-default fair-queue!interface A...
I'm familiar with using IP SLA to track routes, and inject or remove routes based on the tracked object. This question is in regards to icmpecho and multiple targets.Is it possible for me to set up an sla with multiple icmp targets, and if so, what ...
I'm new to this so forgive my Ignorance! For example. Router 1 s0/0 has an address of 192.168.10.1/24.Does Router 2 have to have an address between 192.168.2-254 ? I thought that Serial Interfaces could be on different subnets and still communicat...
(I hope this is the proper place to post a NAT/routing question; if not, please move or let me know)Some time back, I successfully configured a 2811 to do NAT. I am having difficulty with an 1811 router using the same config.Here is the 2811 config ...
Can anyone point me in the right direction, I powered up a 3945 router for the first time today and only noticed on shutting it down that the banner states that you need to change the username/password the first time it is started up ! Who reads the ...
Does anyone out there have a link to any documentation that describes exactly what you get with each technology package license for the Universal IOS images? I have found several vague descriptions but I'd really like a complete list of activated fe...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |
